1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Need help with Mod. 26J (19/89?)
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#3

12-31-2009, 10:14 AM
Is the 26 cabinet completely toast Icon_confused:

Because if it is salvageable at all, it should be restored. The 26 is a very rare bird. Do you have photographs you can share?

An extra Bakelite block was added to the 19 and 89 early in production. It is located close to the antenna coil. Is this the extra block you refer to? I can't help you on the "5 wire gang" as I have never seen a 26, but you are probably right on that.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
Need help with Mod. 26J (19/89?) - by baspas - 12-31-2009, 01:08 AM
Re: Need help with Mod. 26J (19/89?) - by Ron Ramirez - 12-31-2009, 10:14 AM
Re: Need help with Mod. 26J (19/89?) - by baspas - 12-31-2009, 10:50 AM
Re: Need help with Mod. 26J (19/89?) - by baspas - 01-01-2010, 01:30 PM
Re: Need help with Mod. 26J (19/89?) - by baspas - 01-01-2010, 06:59 PM
Re: Need help with Mod. 26J (19/89?) - by exray - 01-02-2010, 09:19 AM
Re: Need help with Mod. 26J (19/89?) - by baspas - 01-02-2010, 12:05 PM
Re: Need help with Mod. 26J (19/89?) - by baspas - 01-02-2010, 02:32 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5192 online users. [Complete List]
» 2 Member(s) | 5190 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration