Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

90 /w/ 1-47...need help
#5

> What impact would this have on the DET.RECT.?
Not much. It's there to filter the a small amount of rf out the the audio signal from the detector. It could be .001mf or 1000mmfd (sorry I don't do nf ) and you wouldn't notice the difference. Now if it was leaky maybe it could cause a problem but there is such a low voltage there that odds are it's not the problem. You can disconnect it to see what happens.

Just abt got all the beer bottles and ashtrays cleaned up so being it over and we can give it the once over.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
90 /w/ 1-47...need help - by bdi1976 - 04-01-2017, 05:01 PM
RE: 90 /w/ 1-47...need help - by morzh - 04-01-2017, 06:47 PM
RE: 90 /w/ 1-47...need help - by Mondial - 04-01-2017, 06:58 PM
RE: 90 /w/ 1-47...need help - by bdi1976 - 04-01-2017, 10:39 PM
RE: 90 /w/ 1-47...need help - by Radioroslyn - 04-01-2017, 11:32 PM
RE: 90 /w/ 1-47...need help - by 45philcodon - 04-02-2017, 04:29 PM
RE: 90 /w/ 1-47...need help - by bdi1976 - 04-02-2017, 08:46 PM
RE: 90 /w/ 1-47...need help - by 45philcodon - 04-03-2017, 12:37 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently 6851 online users. [Complete List]
» 3 Member(s) | 6848 Guest(s)
AvatarAvatarAvatar

>