Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Stromberg Carlson model 60
#1

Starting a new challenge.
[Image: http://i1336.photobucket.com/albums/o654...wwpjrl.jpg]  This is going to be a real challenge to straighten out.
  Notice the added filter can in center upper left side. The tuning cap hits it before you get to 800kz.
   Under side. Lot of scabbing took place.
[Image: http://i1336.photobucket.com/albums/o654...cchcsu.jpg]   The filter can assembly has been bypassed in some sections. I count ten caps in the original can according to schematic. It also has two Philco pots in it.
[Image: http://i1336.photobucket.com/albums/o654...5rsqvh.jpg]
  The capacitor can that has to be rebuilt along with lots of wire tracing.
[Image: http://i1336.photobucket.com/albums/o654...qbaf9u.jpg]   Well it will be a fun challenge anyway and at least the coils all have continuity and power trans. is okay.


Messages In This Thread
Stromberg Carlson model 60 - by KCMike - 04-02-2017, 07:05 PM
RE: Stromberg Carlson model 60 - by Arran - 04-03-2017, 04:05 AM
RE: Stromberg Carlson model 60 - by KCMike - 04-03-2017, 01:40 PM
RE: Stromberg Carlson model 60 - by Radioroslyn - 04-04-2017, 06:03 AM
RE: Stromberg Carlson model 60 - by Arran - 04-04-2017, 10:47 PM
RE: Stromberg Carlson model 60 - by KCMike - 04-05-2017, 05:11 PM
RE: Stromberg Carlson model 60 - by KCMike - 04-08-2017, 01:15 PM
RE: Stromberg Carlson model 60 - by Joe Rossi - 04-09-2017, 08:46 PM
RE: Stromberg Carlson model 60 - by KCMike - 04-10-2017, 09:58 AM
RE: Stromberg Carlson model 60 - by Eric - 06-06-2018, 09:20 AM
RE: Stromberg Carlson model 60 - by KCMike - 06-06-2018, 12:18 PM
RE: Stromberg Carlson model 60 - by Eric - 06-06-2018, 07:25 PM
RE: Stromberg Carlson model 60 - by Eric - 06-14-2018, 04:12 PM
RE: Stromberg Carlson model 60 - by KCMike - 06-14-2018, 04:37 PM
RE: Stromberg Carlson model 60 - by Eric - 06-14-2018, 05:53 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
Philco Predicta Siesta picture over time getting dimmer
I found that the wire insulation was burnt.  The fly back needs corona dope! Why would someone put that there?Platinumblonde36 — 01:09 AM
Philco Predicta Siesta picture over time getting dimmer
This is what it looked like beforePlatinumblonde36 — 01:01 AM

[-]
Who's Online
There are currently no members online.

>