Stromberg Carlson model 60

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Stromberg Carlson model 60

KCMike
Phorum Expert

Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.

04-03-2017, 01:40 PM

Thanks Arran. That's the factory folder I'll be using. I plan to restuff the numbered paper caps and restore the underside of chassis to original as possible.
Not sure what to do about the Philco pots that is it right now. I did do a test power up with an extra parts speaker not original. Missing the original speaker darn it .
I got sound and could hear a station barely in the back ground. So it was time to dig into it.
[Image: http://i1336.photobucket.com/albums/o654...yfrcyh.jpg]
Got to start somewhere so decided to start with the bypass can assembly.
Hard to believe they got ten caps in the little can. Going to be a little tricky to restuff.
[Image: http://i1336.photobucket.com/albums/o654...jatxct.jpg]

Find

« Next Oldest | Next Newest »

Messages In This Thread

Stromberg Carlson model 60 - by KCMike - 04-02-2017, 07:05 PM

RE: Stromberg Carlson model 60 - by Arran - 04-03-2017, 04:05 AM

RE: Stromberg Carlson model 60 - by KCMike - 04-03-2017, 01:40 PM

RE: Stromberg Carlson model 60 - by Radioroslyn - 04-04-2017, 06:03 AM

RE: Stromberg Carlson model 60 - by Arran - 04-04-2017, 10:47 PM

RE: Stromberg Carlson model 60 - by KCMike - 04-05-2017, 05:11 PM

RE: Stromberg Carlson model 60 - by KCMike - 04-08-2017, 01:15 PM

RE: Stromberg Carlson model 60 - by Joe Rossi - 04-09-2017, 08:46 PM

RE: Stromberg Carlson model 60 - by KCMike - 04-10-2017, 09:58 AM

RE: Stromberg Carlson model 60 - by Eric - 06-06-2018, 09:20 AM

RE: Stromberg Carlson model 60 - by KCMike - 06-06-2018, 12:18 PM

RE: Stromberg Carlson model 60 - by Eric - 06-06-2018, 07:25 PM

RE: Stromberg Carlson model 60 - by Eric - 06-14-2018, 04:12 PM

RE: Stromberg Carlson model 60 - by KCMike - 06-14-2018, 04:37 PM

RE: Stromberg Carlson model 60 - by Eric - 06-14-2018, 05:53 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5296 online users. [Complete List]
» 1 Member(s) | 5295 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me