1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
question on a possible philco phonograph/ recorder?
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

01-05-2010, 10:59 AM
I honestly do not know where you might find recording disk blanks.

In the previous Phorum post you linked to, did you write to the fellow who listed his email address?

45honcho Wrote:Well I have good news Icon_biggrin Icon_biggrin Icon_biggrin You can still buy blank records to record on. We restore and sell record cutters all of the time. Obviously, we have to test them before we send them out. We have several blanks that are Philco brand and they work fine. The best ones to use are the cardboard base discs. They won't ruin your cutting needle. The aluminum discs are heavier, but much more delicate to work with. You need to have depth set correctly to use these. The acetate on the NOS Philco discs we use is perfectly fine. They are stored in all different temperatures and no problems. If you would like the recording done for you, contact me at tse1968@45honcho.com and I would be glad to help you out.

He works with phonographs all of the time, so I believe he would be in the best position to help you out.

Your grandmother's set is probably a 1941 or 42 Philco with Beam of Light reproducer and the optional record cutter attachment. As far as I know, Philco did not install record cutters into any of their postwar sets.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
question on a possible philco phonograph/ recorder? - by Guest - 01-04-2010, 11:31 PM
Re: question on a possible philco phonograph/ recorder? - by Ron Ramirez - 01-05-2010, 10:59 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4591 online users. [Complete List]
» 1 Member(s) | 4590 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios