1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 41-608 connector question.
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#4

01-07-2010, 07:47 AM
I'll move this and your other topic to Philco Electronic Restoration for you, Harlan. Icon_smile

Please see the Announcements section - I've just posted a tutorial on how to send private messages (PMs).

While you are of course free to take your conversation private, I hope you will leave it on here - others may benefit from the discussion on this subject.

Thanks.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 41-608 connector question. - by Harlan - 01-06-2010, 09:27 PM
Re: Philco 41-608 connector question. - by Sean - 01-06-2010, 09:43 PM
Re: Philco 41-608 connector question. - by Harlan - 01-06-2010, 10:44 PM
Re: Philco 41-608 connector question. - by Ron Ramirez - 01-07-2010, 07:47 AM
Re: Philco 41-608 connector question. - by Sean - 01-07-2010, 09:14 AM
Re: Philco 41-608 connector question. - by Harlan - 01-07-2010, 10:14 AM
Re: Philco 41-608 connector question. - by Sean - 01-07-2010, 12:00 PM
Re: Philco 41-608 connector question. - by Harlan - 01-07-2010, 06:24 PM
Re: Philco 41-608 connector question. - by Sean - 01-08-2010, 11:19 AM
Re: Philco 41-608 connector question. - by Sean - 01-08-2010, 11:41 PM
Re: Philco 41-608 connector question. - by Harlan - 01-09-2010, 12:03 AM
Re: Philco 41-608 connector question. - by Harlan - 01-10-2010, 06:25 PM
Re: Philco 41-608 connector question. - by Sean - 01-11-2010, 10:07 PM
Re: Philco 41-608 connector question. - by Harlan - 03-29-2010, 09:31 PM
Re: Philco 41-608 connector question. - by Sean - 03-30-2010, 08:19 AM
Re: Philco 41-608 connector question. - by Harlan - 03-30-2010, 09:14 AM
Re: Philco 41-608 connector question. - by Harlan - 03-30-2010, 08:38 PM
Re: Philco 41-608 connector question. - by Sean - 03-31-2010, 07:36 AM
Re: Philco 41-608 connector question. - by Harlan - 03-31-2010, 02:34 PM
Re: Philco 41-608 connector question. - by Sean - 04-01-2010, 08:37 AM
Re: Philco 41-608 connector question. - by Harlan - 04-01-2010, 09:01 AM
Re: Philco 41-608 connector question. - by Guest - 06-12-2010, 12:32 PM
Re: Philco 41-608 connector question. - by Harlan - 10-15-2010, 09:02 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently 414 online users. [Complete List]
» 1 Member(s) | 413 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration