1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
what to do next
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

01-15-2010, 07:23 PM
With the set off flip it over so the bottom is up and you can see all of the tube sockets. Go to one of the 45 tube sockets and connect your minus meter lead to one of the two fatter pins of the 45. It doesn't matter which one. Set your meter for DC volts. The range should be set at 500v if it isn't one that doesn't do it automatically. Turn the set on. Carefully measure the voltages on the two small pins of the 45 tube. Then leave the minus lead where it is and measure the voltages on the two smaller pins on the other 45 tube.
Tell me what'ch got
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
what to do next - by denver - 01-15-2010, 04:22 PM
Re: what to do next - by Carl Travis - 01-15-2010, 04:50 PM
Re: what to do next - by denver - 01-15-2010, 07:06 PM
Re: what to do next - by 7estatdef - 01-15-2010, 07:23 PM
Re: what to do next - by denver - 01-15-2010, 08:24 PM
Re: what to do next - by denver - 01-16-2010, 12:40 PM
Re: what to do next - by 7estatdef - 01-16-2010, 02:39 PM
Re: what to do next - by denver - 01-16-2010, 02:56 PM
Re: what to do next - by 7estatdef - 01-16-2010, 03:00 PM
Re: what to do next - by 7estatdef - 01-16-2010, 03:06 PM
Re: what to do next - by denver - 01-16-2010, 03:34 PM
Re: what to do next - by denver - 01-16-2010, 04:20 PM
Re: what to do next - by 7estatdef - 01-16-2010, 07:27 PM
Re: what to do next - by denver - 01-16-2010, 07:48 PM
Re: what to do next - by 7estatdef - 01-16-2010, 07:50 PM
Re: what to do next - by 7estatdef - 01-16-2010, 08:04 PM
Re: what to do next - by denver - 01-16-2010, 11:22 PM
Re: what to do next - by denver - 01-16-2010, 11:30 PM
Re: what to do next - by 7estatdef - 01-17-2010, 08:47 AM
Re: what to do next - by denver - 01-18-2010, 10:41 AM
Re: what to do next - by 7estatdef - 01-18-2010, 01:39 PM
Re: what to do next - by denver - 01-18-2010, 03:26 PM
Re: what to do next - by denver - 01-18-2010, 04:31 PM
Re: what to do next - by 7estatdef - 01-18-2010, 06:01 PM
Re: what to do next - by 7estatdef - 01-18-2010, 06:33 PM
Re: what to do next - by denver - 01-18-2010, 06:42 PM
Re: what to do next - by 7estatdef - 01-18-2010, 06:58 PM
Re: what to do next - by denver - 01-18-2010, 07:17 PM
Re: what to do next - by 7estatdef - 01-18-2010, 08:59 PM
Re: what to do next - by denver - 01-18-2010, 10:44 PM
Re: what to do next - by 7estatdef - 01-19-2010, 08:18 AM
Re: what to do next - by denver - 01-19-2010, 11:26 AM
Re: what to do next - by 7estatdef - 01-19-2010, 06:34 PM
Re: what to do next - by denver - 01-19-2010, 09:51 PM
Re: what to do next - by denver - 01-20-2010, 04:43 PM
Re: what to do next - by 7estatdef - 01-20-2010, 08:57 PM
Re: what to do next - by denver - 01-20-2010, 09:20 PM
Re: what to do next - by 7estatdef - 01-20-2010, 10:16 PM
Re: what to do next - by denver - 01-21-2010, 01:59 PM
Re: what to do next - by 7estatdef - 01-21-2010, 06:21 PM
Re: what to do next - by denver - 01-21-2010, 07:46 PM
Re: what to do next - by 7estatdef - 01-30-2010, 08:40 AM
Re: what to do next - by denver - 01-30-2010, 04:11 PM



Users browsing this thread: 8 Guest(s)
[-]
Recent Posts
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
12' Philco
Not anymore Mike. Andre The Giant Born: May 19, 1946, Coulommiers, France Died: Jan 28, 1993 (46 years), Paris, Fran...RodB — 11:53 PM
IF can wire size and Rubber mounts?
Renovated Radios do carry what you need. As for the voltage, a wire should be at least 300V-rated.morzh — 11:13 PM
12' Philco
Andre the Giant got 2" on Kareem :lol:morzh — 11:11 PM
IF can wire size and Rubber mounts?
Thanks for the info but I doubt that a hardware store would be carrying the proper tuner assembly support mountings for ...georgetownjohn — 10:38 PM
12' Philco
Perhaps Kareem Abdul Jabbar?GarySP — 10:33 PM
My last cabinet for this year
Outstanding work, Dan! Take care and BE HEALTHY! GaryGarySP — 10:31 PM
My last cabinet for this year
They are a nice looking radio, Stromberg. I have a small tabletop octagon-dial one. It sounds surprisingly nice. And t...morzh — 09:40 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration