46-1226 code 125 restoratioin *DONE
Posts: 619
Threads: 42
Joined: Mar 2017
City: Gap Mills Wv 24941
(05-07-2017, 10:49 PM)Radioroslyn Wrote: >
Grounding the chassis will eliminate this voltage.
3 prong plug in is the solution then i guess, i have 35ohms on my utility ground... so my N leg is fine. My 2011 notes on my panel board say i had no neutral current with my amp clamp either. the garage where i am working doesnt have any motor loads on right now. I'll have to redo my power chord and see if that that helps any.
either way when on short wave i still hear a tiny bit of humm,, it reduces in audibility when a chassis gnd is added.
I was actually thinking the band seletor section is rubber isolated somewhat and thought the error was there. THen i looked again and see Philco has a jumper wire from the chassis of the main section to the chasssis of the tuner section so...... i was wrong there.
on my hallicrafers the rubber isolators keep the exterior completly isolated from the radio.
(This post was last modified: 05-08-2017, 07:01 AM by jcassity.)
Messages In This Thread
RE: 46-1226 code 125 restoratioin - by jcassity - 05-08-2017, 06:47 AM
Users browsing this thread: 16 Guest(s)
|
|
Recent Posts
|
|
Made mistake & did not label connection
|
| I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM |
|
Made mistake & did not label connection
|
| What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM |
|
Made mistake & did not label connection
|
| Hello John,
I have been there either label got lost or was not labeled !
Sincerely Richardradiorich — 02:15 PM |
|
Made mistake & did not label connection
|
| Sorry, it is a Philco 37-640. Does that help?--Johngeorgetownjohn — 02:14 PM |
|
two videos to watch VHS and history of TV
|
| Hello Every,
Here are a couple videos right up my alley VHS and the history of Television .
history of VCR VHS
Hi...radiorich — 02:13 PM |
|
Made mistake & did not label connection
|
| You haven't given us the model number of the set so I looked up the 6A8 pin assignment. Pin 8 is the cathode and pin 7 i...RodB — 01:19 PM |
|
Made mistake & did not label connection
|
| Happy Thanksgiving all!
I have made a real bonehead mistake this time. Hope someone can help. I am trying to determi...georgetownjohn — 12:51 PM |
|
New Philco Repair Bench
|
| Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM |
|
Philco 60 Squealing
|
| Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM |
|
Philco 60 Squealing
|
| Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture.
dconant — 09:21 AM |
|
Who's Online
|
There are currently 2790 online users. [Complete List]
» 2 Member(s) | 2788 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
