Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Conar 223
#1

I bought a Conar 223 for a decent price. I need to replace the bulb that displays if there's a short, but otherwise it looks like it just sat in an attic for years.

I wanted something simple to start with, that doesn't have a complex calibration procedure. The only calibration to do on this is replace caps and resistors when they go out of spec. I'll check and replace those as needed next week.

Setup is pretty simple following the data sheets. I tested a couple of 71A tubes yesterday just for kicks, both were in the "good" range (can't check for shorts since the bulb is broken, will buy a new one soon). However, I'm not exactly sure is I'm testing my 27 tube correctly... it has 5 pins and after rotating it enough I was able to line it up and insert using the same socket as the 4-pin 71As. When I followed the test procedure the needle went all the way left, which tells me either my 27 is bad or I did the test wrong.

My question is, does anyone else have a Conar 223 and if so, am I using the right socket for the 5-pin 27 tube?

Also, I'm guessing the wire lead with the clip on top is for testing my #24 tubes?

Greg

"We are here to laugh at the odds and live our lives so well that Death will tremble to take us."


Messages In This Thread
Conar 223 - by WallaceRoger - 05-11-2017, 01:58 PM
RE: Conar 223 - by Radioroslyn - 05-11-2017, 02:21 PM
RE: Conar 223 - by WallaceRoger - 05-12-2017, 11:58 AM
RE: Conar 223 - by WallaceRoger - 05-12-2017, 02:20 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM
Looking for verification of correct schematic.
Klondike98, Thank you. I'll double check that SN and get back to you. GarySP, Thank you for the schematic.RossH — 12:13 AM

[-]
Who's Online
There are currently 1948 online users. [Complete List]
» 1 Member(s) | 1947 Guest(s)
Avatar

>