One of the spoils

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

One of the spoils

Radioroslyn
Phorum Expert

Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa

05-18-2017, 06:18 AM

VC showed about 2K when turned all the way CCW and the same when turned all the way CW and measured from the other end. Cleaning didn't help. It took a few tries to find one that didn't advance too much at low levels indicating the wrong taper but found a suitable replacement.
For a portable set it plays really loud, sounds like it has a 50L6 rather than a 3Q5.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

One of the spoils - by Radioroslyn - 05-14-2017, 03:48 PM

RE: One of the spoils - by sam - 05-14-2017, 05:33 PM

RE: One of the spoils - by WallaceRoger - 05-14-2017, 07:06 PM

RE: One of the spoils - by sam - 05-14-2017, 07:37 PM

RE: One of the spoils - by Mondial - 05-14-2017, 07:41 PM

RE: One of the spoils - by Radioroslyn - 05-14-2017, 08:29 PM

RE: One of the spoils - by Radioroslyn - 05-18-2017, 06:18 AM

RE: One of the spoils - by OldRestorer - 05-18-2017, 07:22 AM

RE: One of the spoils - by sam - 05-18-2017, 10:34 AM

RE: One of the spoils - by OldRestorer - 05-18-2017, 11:36 AM

RE: One of the spoils - by sam - 05-18-2017, 11:42 AM

RE: One of the spoils - by Radioroslyn - 05-23-2017, 10:07 AM

RE: One of the spoils - by Radioroslyn - 05-23-2017, 10:09 AM

RE: One of the spoils - by sam - 05-23-2017, 10:25 AM

RE: One of the spoils - by Radioroslyn - 05-23-2017, 01:49 PM

RE: One of the spoils - by OldRestorer - 05-23-2017, 03:13 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me