1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
PT96 - low plate voltage
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#9

01-27-2010, 06:25 PM
Hmmmm. Check voltage from pin 8 (neg) to pin 5 (pos) of the 50L6 with all tube in place. Should see - 10v or so. If positive voltage cap on pin 5 is leaky.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
PT96 - low plate voltage - by Carl Travis - 01-23-2010, 10:39 AM
Re: PT96 - low plate voltage - by 7estatdef - 01-23-2010, 09:46 PM
Re: PT96 - low plate voltage - by Carl Travis - 01-24-2010, 10:51 AM
Re: PT96 - low plate voltage - by codefox1 - 01-24-2010, 12:13 PM
Re: PT96 - low plate voltage - by Carl Travis - 01-25-2010, 11:42 AM
Re: PT96 - low plate voltage - by 7estatdef - 01-25-2010, 01:28 PM
Re: PT96 - low plate voltage - by codefox1 - 01-25-2010, 02:26 PM
Re: PT96 - low plate voltage - by Carl Travis - 01-27-2010, 12:14 PM
Re: PT96 - low plate voltage - by 7estatdef - 01-27-2010, 06:25 PM
Re: PT96 - low plate voltage - by 7estatdef - 01-27-2010, 07:04 PM
Re: PT96 - low plate voltage - by codefox1 - 01-27-2010, 08:50 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5108 online users. [Complete List]
» 1 Member(s) | 5107 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration