Eico Model 315 SG

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Eico Model 315 SG

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

06-18-2017, 11:31 PM

OK, I recapped all Capacitors.. I checked all Resistors and they were all within 10%..

So I hooked it up to my Spectrum ANA and saw a very nice signal.. around between -20 Dbm to -19 dbm max''

Someone had soldered close the part that houses the Attenuator resistors so I didn't check them out yet..

I checked out all bands and did a calibration .. All looks good now.. It doesn't put out a sine wave but the waveform isn't to bad looking..

I will check the attenuator resistors and do a cosmetic restoration.. OH and change out the connectors to BNC..then it should be good to go..

Skip...

Find

« Next Oldest | Next Newest »

Messages In This Thread

Eico Model 315 SG - by vecher - 06-15-2017, 10:58 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-15-2017, 11:48 PM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 03:51 PM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 06:19 PM

RE: Eico Model 315 SG - by Eliot Ness - 06-16-2017, 08:49 PM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 09:45 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-16-2017, 09:54 PM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 09:59 PM

RE: Eico Model 315 SG - by vecher - 06-18-2017, 11:31 PM

RE: Eico Model 315 SG - by vecher - 06-22-2017, 10:15 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-23-2017, 12:37 AM

RE: Eico Model 315 SG - by vecher - 06-23-2017, 10:03 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-23-2017, 10:51 PM

RE: Eico Model 315 SG - by vecher - 06-23-2017, 11:33 PM

RE: Eico Model 315 SG - by vecher - 06-24-2017, 08:37 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

Who's Online

There are currently 2546 online users. [Complete List]
» 1 Member(s) | 2545 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me