1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Testing a 45 Tube
morzh
Odobenus rosmarus
*****
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
#2

06-20-2017, 03:25 PM
I have this with many tubes on my 600A, when I push the P4 and see the needle going up and then slowly dropping a bit. Not too much but it will drop. I consider this "good".
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Testing a 45 Tube - by Phlogiston - 06-20-2017, 01:38 PM
RE: Testing a 45 Tube - by morzh - 06-20-2017, 03:25 PM
RE: Testing a 45 Tube - by Phlogiston - 06-20-2017, 04:05 PM
RE: Testing a 45 Tube - by klondike98 - 06-20-2017, 07:38 PM
RE: Testing a 45 Tube - by TV MAN - 06-22-2017, 02:48 PM
RE: Testing a 45 Tube - by Phlogiston - 06-22-2017, 05:48 PM
RE: Testing a 45 Tube - by Arran - 06-22-2017, 09:23 PM
RE: Testing a 45 Tube - by Phlogiston - 06-23-2017, 09:58 AM
RE: Testing a 45 Tube - by Phlogiston - 08-08-2018, 09:04 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Not sure if anyone has tried this but there are 6.3 volt miniature lamps in bayonet and screw-in base options available ...GarySP — 11:31 AM
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment