41-280 some parts don't jive w/ schematic, picture included

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

41-280 some parts don't jive w/ schematic, picture included

Elrick
Junior Member

Posts: 18
Threads: 9
Joined: Jan 2010

02-01-2010, 06:02 PM

I heated and dug out the black goo and found the hidden caps in the process. While I was digging the tar material out I managed to sever the cap leads that connects to the power line though the bakelite housing, the leads that went to the ground were remained connected. In an effort to simplify things, I decided to mount the caps on the outside. Each Cap is connected to one side of the power line, and then each cap is grounded to the screw that mounts the bakelite housing. Am I doing this correct?

[Image: http://i103.photobucket.com/albums/m140/...3_1082.jpg]

Also are these caps going to be hot whenever the radio is plugged in?

Find

« Next Oldest | Next Newest »

Messages In This Thread

41-280 some parts don't jive w/ schematic, picture included - by Elrick - 01-31-2010, 04:03 PM

Re: 41-280 some parts don't jive w/ schematic, picture included - by 7estatdef - 02-01-2010, 12:42 PM

Re: 41-280 some parts don't jive w/ schematic, picture included - by Elrick - 02-01-2010, 03:57 PM

Re: 41-280 some parts don't jive w/ schematic, picture included - by Elrick - 02-01-2010, 06:02 PM

Re: 41-280 some parts don't jive w/ schematic, picture included - by 7estatdef - 02-01-2010, 07:14 PM

Re: 41-280 some parts don't jive w/ schematic, picture included - by codefox1 - 02-02-2010, 12:33 PM

Re: 41-280 some parts don't jive w/ schematic, picture included - by Chuck Schwark - 02-02-2010, 02:18 PM

Re: 41-280 some parts don't jive w/ schematic, picture included - by Elrick - 02-08-2010, 10:01 AM

Re: 41-280 some parts don't jive w/ schematic, picture included - by 7estatdef - 02-08-2010, 01:33 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5070 online users. [Complete List]
» 2 Member(s) | 5068 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me