Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Hippo 48-460 code 122
#2

Mike,
  I'm trying to remember how it disconnects, I think it has a setup where it's pulled by a spring on one end, and the dial cord on the other, by that big drum pulley on top of the tuning condenser, so you slip the cord off the back of the pointer somehow. It's been a few years since I dealt with a hippo, but I can pull one out of storage and have a look.
Regards
Arran


Messages In This Thread
Hippo 48-460 code 122 - by morzh - 06-30-2017, 08:52 PM
RE: Hippo 48-460 code 122 - by Arran - 06-30-2017, 10:54 PM
RE: Hippo 48-460 code 122 - by morzh - 07-01-2017, 10:56 AM
RE: Hippo 48-460 code 122 - by morzh - 07-01-2017, 02:19 PM
RE: Hippo 48-460 code 122 - by morzh - 07-01-2017, 07:24 PM
RE: Hippo 48-460 code 122 - by Radioroslyn - 07-01-2017, 09:04 PM
RE: Hippo 48-460 code 122 - by morzh - 07-01-2017, 10:22 PM
RE: Hippo 48-460 code 122 - by Arran - 07-01-2017, 11:14 PM
RE: Hippo 48-460 code 122 - by morzh - 07-02-2017, 10:43 PM
RE: Hippo 48-460 code 122 - by Arran - 07-02-2017, 11:05 PM
RE: Hippo 48-460 code 122 - by morzh - 07-03-2017, 02:29 PM
RE: Hippo 48-460 code 122 - by morzh - 07-03-2017, 09:20 PM
RE: Hippo 48-460 code 122 - by morzh - 07-03-2017, 09:32 PM
RE: Hippo 48-460 code 122 - by KCMike - 07-03-2017, 09:38 PM
RE: Hippo 48-460 code 122 - by Radioroslyn - 07-03-2017, 09:43 PM
RE: Hippo 48-460 code 122 - by klondike98 - 07-03-2017, 09:45 PM
RE: Hippo 48-460 code 122 - by morzh - 07-03-2017, 09:59 PM
RE: Hippo 48-460 code 122 - by Radioroslyn - 07-03-2017, 10:18 PM
RE: Hippo 48-460 code 122 - by morzh - 07-04-2017, 06:34 PM
RE: Hippo 48-460 code 122 - by morzh - 07-04-2017, 06:35 PM
RE: Hippo 48-460 code 122 - by NostalgiaRadioTime - 07-04-2017, 06:39 PM
RE: Hippo 48-460 code 122 - by morzh - 07-04-2017, 07:21 PM
RE: Hippo 48-460 code 122 - by WallaceRoger - 07-05-2017, 11:12 AM
RE: Hippo 48-460 code 122 - by Radioguy52 - 01-15-2022, 03:32 PM
RE: Hippo 48-460 code 122 - by morzh - 01-15-2022, 06:19 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5658 online users. [Complete List]
» 2 Member(s) | 5656 Guest(s)
AvatarAvatar

>