Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 89 veneer missing
#13

Got a little surprise today when I tried to dry fit the arch.  The slot in the original front panel is 1/8" but the new arch is about 5/32".  Luckily I have the small Dremel router attachment and I was able to widen it (slowly & carefully) with a 1/8" bit.  Ready now for clear coat and grain filler.  Steve, you mentioned applying clear lacquer first then the grain filler.  Will the filler adhere well to the clear coat.  That was my only concern.

***********
Dave Thomas
Coatesville, PA


Messages In This Thread
Philco 89 veneer missing - by RadioDR401 - 03-07-2017, 08:00 PM
RE: Philco 89 veneer missing - by John Bartley - 03-08-2017, 07:12 AM
RE: Philco 89 veneer missing - by Steve Davis - 03-08-2017, 09:29 AM
RE: Philco 89 veneer missing - by Radioroslyn - 03-10-2017, 08:40 PM
RE: Philco 89 veneer missing - by Arran - 03-13-2017, 12:54 AM
RE: Philco 89 veneer missing - by Steve Davis - 03-13-2017, 09:29 PM
RE: Philco 89 veneer missing - by Arran - 03-13-2017, 09:43 PM
RE: Philco 89 veneer missing - by RadioDR401 - 03-14-2017, 10:42 AM
RE: Philco 89 veneer missing - by Steve Davis - 03-14-2017, 12:27 PM
RE: Philco 89 veneer missing - by Arran - 03-14-2017, 06:50 PM
RE: Philco 89 veneer missing - by RadioDR401 - 07-04-2017, 10:41 AM
RE: Philco 89 veneer missing - by Steve Davis - 07-04-2017, 01:07 PM
RE: Philco 89 veneer missing - by RadioDR401 - 07-05-2017, 03:28 PM
RE: Philco 89 veneer missing - by Phlogiston - 07-05-2017, 05:13 PM
RE: Philco 89 veneer missing - by RadioDR401 - 07-06-2017, 06:18 AM
RE: Philco 89 veneer missing - by Phlogiston - 07-06-2017, 09:33 AM
RE: Philco 89 veneer missing - by RadioDR401 - 08-29-2017, 11:40 AM
RE: Philco 89 veneer missing - by RadioDR401 - 09-09-2017, 02:33 PM
RE: Philco 89 veneer missing - by Phlogiston - 09-09-2017, 03:05 PM
RE: Philco 89 veneer missing - by Scott D - 09-09-2017, 04:15 PM
RE: Philco 89 veneer missing - by RadioDR401 - 03-05-2018, 04:09 PM
RE: Philco 89 veneer missing - by sdradioman - 03-05-2018, 09:07 PM
RE: Philco 89 veneer missing - by Radioroslyn - 03-05-2018, 10:46 PM
RE: Philco 89 veneer missing - by RadioDR401 - 03-06-2018, 09:49 AM



Users browsing this thread:
[-]
Recent Posts
Correct model 84 Ac plug an cord type
Hello Arran Yes, I also like the lampshade style plug ! Sincerely Richardradiorich — 08:46 AM
Restoring Philco 38-14
Hello morzh, Nice explanation on the x and y capacitors and glad you are narrowing down the issue with this set ! Si...radiorich — 08:43 AM
Correct model 84 Ac plug an cord type
From what I read Philco went to using brown rubber power cords in 1936, so cloth was used in the 1935 and earlier models...Arran — 11:25 PM
Correct model 84 Ac plug an cord type
Hi Bruce, I have not worked on an 84, but in general, power cords for almost any radio prior to 1938 was cloth covered...MrFixr55 — 08:34 PM
Restoring Philco 38-14
OK, well, so after staring at the sch again, I realized the problem had to be the #12/12A padder. I put a scope on the o...morzh — 08:15 PM
Correct model 84 Ac plug an cord type
Hello Bruce, I mostly use brown far as my cloth powercords go ! Here is the plug that I have used bakelite Acorn style...radiorich — 08:05 PM
Correct model 84 Ac plug an cord type
Looking for as correct as can find the right Ac plug an the correct colored cloth line. Ive seen many old photos but mos...Bruce — 04:13 PM
Restoring Philco 38-14
Rod Two Y-caps make sense if you use them from L/N to the chassis; this is only makes sense in the transformer radios...morzh — 10:11 AM
Restoring Philco 38-14
Mike, I'm curious about a specific use of he Y cap. Lately I've seen a single cap across the power transformer primary. ...RodB — 09:01 AM
Restoring Philco 38-14
hello morzh , That sounds like a plan ! Sincerely Richardradiorich — 07:45 AM

[-]
Who's Online
There are currently 4617 online users. [Complete List]
» 1 Member(s) | 4616 Guest(s)
Avatar

>