Model 370 chairside

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Model 370 chairside

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

02-06-2010, 12:27 PM

Yup Veneer is all there but it does have a pretty good burn in it and a little chipping on the edges. It is miss about 6 of little half round pieces of trim. But shouldn't be hard to replicate with some dowel stock. There was one up on ebay awhile back it was kinda a mess it too had the top reveneered. I was thinking about seeing if bottom half of the cabinet could be had as mine as a couple of extra holes in the side. But never did anything about it.
Tnx for the encouragement!
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Model 370 chairside - by 7estatdef - 01-27-2010, 10:59 PM

Re: Model 370 chairside - by Ron Ramirez - 02-05-2010, 08:06 PM

Re: Model 370 chairside - by 7estatdef - 02-06-2010, 12:27 PM

Re: Model 370 chairside - by 7estatdef - 02-06-2010, 11:04 PM

Re: Model 370 chairside - by Ron Ramirez - 02-07-2010, 08:08 AM

Re: Model 370 chairside - by Ron Ramirez - 02-07-2010, 09:10 AM

Re: Model 370 chairside - by 7estatdef - 02-07-2010, 11:05 AM

Re: Model 370 chairside - by Ron Ramirez - 02-07-2010, 12:38 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me