1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Nathan's Philco 118MX
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#12

07-20-2017, 04:57 PM
(07-18-2017, 11:12 PM)Nathan Slingerland Wrote:  I haven't glued large pieces of veneer before so this will be a learning opportunity. Any advice an adhesive? I've been considering 'Heat Lock' since it seems to be intended for raw veneer like this: http://www.veneersupplies.com/products/B...-Glue.html
Has anyone tried this previously? Other suggestions?

Several years ago, I had a 38-116. One entire side of veneer had come off. I think I used contact cement and a roller to reattach it. I'm not sure I would use contact cement again, though, as I have since read that there is a good chance that it could come off again. Hopefully Steve or Russ will chime in.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
Nathan's Philco 118MX - by Nathan Slingerland - 07-04-2017, 09:13 PM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 07-04-2017, 09:17 PM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 07-04-2017, 09:24 PM
RE: Nathan's Philco 118MX - by Ron Ramirez - 07-05-2017, 05:04 AM
RE: Nathan's Philco 118MX - by OldRestorer - 07-05-2017, 05:41 AM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 07-05-2017, 08:59 AM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 07-06-2017, 10:36 PM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 07-18-2017, 11:12 PM
RE: Nathan's Philco 118MX - by klondike98 - 07-19-2017, 07:05 AM
RE: Nathan's Philco 118MX - by OldRestorer - 07-19-2017, 07:24 AM
RE: Nathan's Philco 118MX - by Radioroslyn - 07-19-2017, 09:29 AM
RE: Nathan's Philco 118MX - by Ron Ramirez - 07-20-2017, 04:57 PM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 07-20-2017, 05:11 PM
RE: Nathan's Philco 118MX - by Bob Andersen - 07-21-2017, 04:40 PM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 07-21-2017, 07:16 PM
RE: Nathan's Philco 118MX - by OldRestorer - 07-23-2017, 11:13 AM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 08-04-2017, 09:43 PM
RE: Nathan's Philco 118MX - by OldRestorer - 08-05-2017, 10:22 AM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 08-05-2017, 11:00 AM
RE: Nathan's Philco 118MX - by klondike98 - 08-05-2017, 04:31 PM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 08-05-2017, 08:41 PM
RE: Nathan's Philco 118MX - by Nathan Slingerland - 08-06-2017, 05:33 PM
RE: Nathan's Philco 118MX - by Fred Taylor - 08-07-2017, 06:22 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration