1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
53-1750 Alignment question
Radioroslyn
Phorum Expert
*****
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#11

07-27-2017, 01:30 PM
If you are in doubt use an ac voltmeter and measure the ac voltage between the two chassis. If there is 120vac you'll either get a nasty shock or pop ur breaker w/a big spark. Don't ask me how I know[Image: http://philcoradio.com/phorum/images/smi...lleyes.gif] Or you can ask the birthday boy.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 07-27-2017, 01:31 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
53-1750 Alignment question - by ODPILOT - 07-24-2017, 05:53 PM
RE: 53-1750 Alignment question - by Radioroslyn - 07-24-2017, 06:47 PM
RE: 53-1750 Alignment question - by ODPILOT - 07-24-2017, 09:36 PM
RE: 53-1750 Alignment question - by morzh - 07-24-2017, 10:06 PM
RE: 53-1750 Alignment question - by Radioroslyn - 07-24-2017, 10:24 PM
RE: 53-1750 Alignment question - by klondike98 - 07-24-2017, 10:35 PM
RE: 53-1750 Alignment question - by ODPILOT - 07-27-2017, 08:41 AM
RE: 53-1750 Alignment question - by Radioroslyn - 07-27-2017, 10:11 AM
RE: 53-1750 Alignment question - by morzh - 07-27-2017, 10:34 AM
RE: 53-1750 Alignment question - by ODPILOT - 07-27-2017, 12:53 PM
RE: 53-1750 Alignment question - by Radioroslyn - 07-27-2017, 01:30 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

[-]
Who's Online
There are currently 6322 online users. [Complete List]
» 1 Member(s) | 6321 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration