1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Started in on a 41-300
Radioroslyn
Phorum Expert
*****
Posts: 7,297
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#3

07-29-2017, 01:19 PM
Dug up a hammond 125 series output transformer but is too large to mount under the chassis. Next is a Thordarson 24S11 fits very nicely but have to do some guess work to come up w/the proper match and feedback point. Have plenty of options as it's a mulitimatch. Also found what I think will be a good replacement for the off/on switch. Should be getting it in the next few days.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 07-29-2017, 01:22 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Started in on a 41-300 - by Radioroslyn - 07-29-2017, 12:38 AM
RE: Started in on a 41-300 - by sam - 07-29-2017, 01:09 AM
RE: Started in on a 41-300 - by Radioroslyn - 07-29-2017, 01:19 PM
RE: Started in on a 41-300 - by Radioroslyn - 07-29-2017, 03:29 PM
RE: Started in on a 41-300 - by klondike98 - 07-29-2017, 06:03 PM
RE: Started in on a 41-300 - by Radioroslyn - 07-29-2017, 09:14 PM
RE: Started in on a 41-300 - by Radioroslyn - 08-03-2017, 04:43 PM
RE: Started in on a 41-300 - by Radioroslyn - 08-03-2017, 10:52 PM
RE: Started in on a 41-300 - by Radioroslyn - 08-09-2017, 08:12 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1030 online users. [Complete List]
» 1 Member(s) | 1029 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration