1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Condenser working voltages?
wu8v
Junior Member
**
Posts: 16
Threads: 8
Joined: Feb 2010
#3

02-14-2010, 10:12 PM
It is a 37-9.

I have also been having a problem sourcing the 1000V (or more) 30-4469 that is in there. What are you guys using for some of the high voltage caps? and where are you getting them, Mouser does not have any mylars of that high a working voltage... do you have a mouser number for what you are using?

Thanks,
Kurt
Find
« Next Oldest | Next Newest »


Messages In This Thread
Condenser working voltages? - by wu8v - 02-14-2010, 05:10 PM
Re: Condenser working voltages? - by exray - 02-14-2010, 10:04 PM
Re: Condenser working voltages? - by wu8v - 02-14-2010, 10:12 PM
Re: Condenser working voltages? - by exray - 02-14-2010, 10:19 PM
Re: Condenser working voltages? - by wu8v - 02-14-2010, 10:27 PM
Re: Condenser working voltages? - by exray - 02-14-2010, 10:32 PM
Re: Condenser working voltages? - by wu8v - 02-14-2010, 10:57 PM
Re: Condenser working voltages? - by Ron Ramirez - 02-15-2010, 11:11 AM
Re: Condenser working voltages? - by exray - 02-15-2010, 09:55 PM
Re: Condenser working voltages? - by Jim Berg - 02-17-2010, 02:44 PM
Re: Condenser working voltages? - by Alan Douglas - 02-17-2010, 11:31 PM
Re: Condenser working voltages? - by 37-670 - 04-11-2010, 10:06 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration