Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 89 Dial stringing
#4

Heres another question, anyone know what the collapsed length of the spring is? I have a box full of springs here but I'd like to avoid the experimentation portion of restringing this.


Messages In This Thread
Philco 89 Dial stringing - by Jim Dutridge - 08-01-2017, 05:35 PM
RE: Philco 89 Dial stringing - by morzh - 08-01-2017, 09:13 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-04-2017, 02:58 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-04-2017, 03:29 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-06-2017, 04:55 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-11-2017, 07:32 PM
RE: Philco 89 Dial stringing - by Radioroslyn - 08-11-2017, 09:29 PM
RE: Philco 89 Dial stringing - by Ron Ramirez - 08-12-2017, 09:58 AM
RE: Philco 89 Dial stringing - by Arran - 08-12-2017, 05:19 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-13-2017, 12:22 PM
RE: Philco 89 Dial stringing - by sam - 08-14-2017, 10:32 AM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-14-2017, 04:24 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-18-2017, 05:24 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-19-2017, 12:30 PM
RE: Philco 89 Dial stringing - by Ron Ramirez - 08-19-2017, 12:56 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-19-2017, 02:59 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-19-2017, 04:42 PM
RE: Philco 89 Dial stringing - by Ron Ramirez - 08-19-2017, 06:35 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-21-2017, 04:49 PM
RE: Philco 89 Dial stringing - by Ron Ramirez - 08-21-2017, 05:44 PM
RE: Philco 89 Dial stringing - by klondike98 - 08-21-2017, 08:42 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 08-22-2017, 05:12 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 09-09-2017, 02:09 PM
RE: Philco 89 Dial stringing - by sam - 09-09-2017, 03:03 PM
RE: Philco 89 Dial stringing - by Jim Dutridge - 09-09-2017, 03:21 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM

[-]
Who's Online
There are currently 3939 online users. [Complete List]
» 1 Member(s) | 3938 Guest(s)
Avatar

>