1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Condenser working voltages?
exray
Phorum Expert
*****
Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA State, Province, Country: PR
#9

02-15-2010, 09:55 PM
Ron Ramirez Wrote:As a general rule, you can replace nearly all paper caps with new ones rated at 600 or 630 VDC. .

I do as well. Not much point in stocking 200, 400, etc volts. The 630v are only a few pennies more and it would cost me a whole nuther cabinet to store a bunch of smaller voltages that might not get much use. Same with resistors. I normally buy 1 watters for general use.
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Condenser working voltages? - by wu8v - 02-14-2010, 05:10 PM
Re: Condenser working voltages? - by exray - 02-14-2010, 10:04 PM
Re: Condenser working voltages? - by wu8v - 02-14-2010, 10:12 PM
Re: Condenser working voltages? - by exray - 02-14-2010, 10:19 PM
Re: Condenser working voltages? - by wu8v - 02-14-2010, 10:27 PM
Re: Condenser working voltages? - by exray - 02-14-2010, 10:32 PM
Re: Condenser working voltages? - by wu8v - 02-14-2010, 10:57 PM
Re: Condenser working voltages? - by Ron Ramirez - 02-15-2010, 11:11 AM
Re: Condenser working voltages? - by exray - 02-15-2010, 09:55 PM
Re: Condenser working voltages? - by Jim Berg - 02-17-2010, 02:44 PM
Re: Condenser working voltages? - by Alan Douglas - 02-17-2010, 11:31 PM
Re: Condenser working voltages? - by 37-670 - 04-11-2010, 10:06 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6031 online users. [Complete List]
» 3 Member(s) | 6028 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration