1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
1941 Philco push button on/off switches
dberman51
Junior Member
**
Posts: 18
Threads: 1
Joined: Feb 2010
#10

03-09-2010, 08:37 PM
Whoever restored my 41-250 did a nice job on the power switch replacement. He fabricated a small aluminum plate to hold a common push-on/push-off lamp switch (any hardware store) and attached it to the back of the push-button assembly with screws and threaded spacers. It looks like he had to trim the plastic actuating button of the new switch a little bit. The assembly just clears the tuning coils behind.

-David
Find
« Next Oldest | Next Newest »


Messages In This Thread
[No subject] - by Ron Ramirez - 11-22-2005, 12:50 AM
[No subject] - by Bill Hutchinson - 11-22-2005, 08:05 PM
Success! - by Raleigh - 06-13-2007, 06:23 PM
[No subject] - by rickd - 06-16-2008, 03:22 PM
[No subject] - by Chuck Schwark - 06-16-2008, 04:08 PM
[No subject] - by rickd - 06-16-2008, 05:07 PM
Re: 1941 Philco push button on/off switches - by dberman51 - 03-09-2010, 08:37 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 4470 online users. [Complete List]
» 3 Member(s) | 4467 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration