Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 46-350
#4

Hi Terry,

I verified voltages again and I got the following measures:

** Values in parenthesis are the expected according to wiring diagram http://www.nostalgiaair.org/PagesByModel...013633.pdf

3LF4 1 - 7 : 1.49 v
1 - 8 : 2.74 v
7 - 8 : 1.25 v
7 : 120 v AC (77 v AC)
2 : 84 v (72v )
3 : 87 v (74v)
6 : 1.6 v (~9v)

1U5 1 - 7 : 1.71 v
2 : 25 v (9v)
3 : 14.9 v (16v)
4 : 1.6 v
6 : 1.1 v

1T4 1 - 7 : 1.42 v
IF Amp 2 : 87 v (76v)
3 : 65 v (45v)
6 : 3.4 v

1R5 1 - 7 : 1.74 v
Converter 2 : 86.7 v (76v)
3 : 65.1 v (45v)
4 : 0 v (0.5 - 2.5v)
6 : 0.76 v

1T4 1 - 7 : 1.66 v
RF Amp 2 : 86.6 v (76v)
3 : 65.1 v (45v)
5 : 3.4 v
6 : 0.2 v

I am following the 48-360 wiring diagram since this radio uses the 3LF4 amplifier and after checking the wiring it fits that wiring.

Regards!

Frank Tovar


Messages In This Thread
Philco 46-350 - by ftovar72 - 10-09-2017, 12:00 AM
RE: [split] Philco 46-350 - by sam - 10-09-2017, 12:24 AM
RE: [split] Philco 46-350 - by Radioroslyn - 10-09-2017, 12:31 AM
RE: Philco 46-350 - by ftovar72 - 10-09-2017, 08:51 PM
RE: Philco 46-350 - by Radioroslyn - 10-09-2017, 10:28 PM
RE: Philco 46-350 - by Raleigh - 10-10-2017, 10:01 AM
RE: Philco 46-350 - by ftovar72 - 10-10-2017, 12:11 PM
RE: Philco 46-350 - by Raleigh - 10-10-2017, 01:18 PM
RE: Philco 46-350 - by ftovar72 - 10-10-2017, 11:55 PM
RE: Philco 46-350 - by Raleigh - 10-11-2017, 09:56 AM
RE: Philco 46-350 - by ftovar72 - 10-12-2017, 06:12 PM
RE: Philco 46-350 - by David - 10-12-2017, 06:50 PM
RE: Philco 46-350 - by ftovar72 - 10-13-2017, 12:01 AM
RE: Philco 46-350 - by Raleigh - 10-14-2017, 08:53 AM
RE: Philco 46-350 - by ftovar72 - 10-14-2017, 08:58 AM
RE: Philco 46-350 - by ftovar72 - 10-18-2017, 10:02 PM
RE: Philco 46-350 - by ftovar72 - 01-08-2018, 12:03 AM
RE: Philco 46-350 - by Radioroslyn - 01-08-2018, 12:40 PM
RE: Philco 46-350 - by ftovar72 - 02-04-2018, 12:56 AM
RE: Philco 46-350 - by ftovar72 - 02-13-2018, 11:06 AM
RE: Philco 46-350 - by codefox1 - 02-14-2018, 04:58 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1091 online users. [Complete List]
» 3 Member(s) | 1088 Guest(s)
AvatarAvatarAvatar

>