Signal Generator

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Signal Generator

tkibler
Junior Member

Posts: 34
Threads: 6
Joined: May 2017
City: Huntington, WV.

10-17-2017, 10:21 AM

Hey everyone! I am looking to purchase a good signal generator to do some alignments. Can I get some ideas from some members on what to buy. Not to pricey...I need to buy more radios!

Find

« Next Oldest | Next Newest »

Messages In This Thread

Signal Generator - by tkibler - 10-17-2017, 10:21 AM

RE: Signal Generator - by morzh - 10-17-2017, 10:26 AM

RE: Signal Generator - by Radioroslyn - 10-17-2017, 11:09 AM

RE: Signal Generator - by WallaceRoger - 10-17-2017, 11:25 AM

RE: Signal Generator - by tkibler - 10-17-2017, 11:40 AM

RE: Signal Generator - by morzh - 10-17-2017, 01:18 PM

RE: Signal Generator - by WallaceRoger - 10-18-2017, 03:39 PM

RE: Signal Generator - by morzh - 10-18-2017, 04:40 PM

RE: Signal Generator - by KCMike - 10-18-2017, 05:02 PM

RE: Signal Generator - by morzh - 10-18-2017, 06:41 PM

RE: Signal Generator - by TA Forbes - 06-14-2018, 08:53 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM

Who's Online

There are currently 7875 online users. [Complete List]
» 2 Member(s) | 7873 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me