Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

41-616 restoration
#1

Ron, 

I really enjoy reading this thread [edit by moderator: the thread referred to here was in the Restoration Notes section] as i just started on my 41-616 tonight still cleaning it, there were mice,yuck.  But have been looking over the capacitors and trying to figure out new ones to order, and im stumped.

 First what is the voltage on the 30 mfd electrolytic one (philco 30-2377) that was mounted to the bottom of the volume motor? Is it a non polarized one like the 16 mfd? And why did yours wind up being so large is there something really special about it?

Also the why is the 125mfd capacitor number 100 on the parts list 25mfd on the schematic? How can there be such a discrepancy between the parts list and the schematic?

Also on the schematic and parts list a condeser is listed as being in the power plug, but no values are given can you give any insight on this? And also on what fuses to install on power cord? 

Finally on my radio theres an unusual added potentiometer clamped to the front of the chassis and wired into the left most pushbutton, any ideas?

  Photo shows potentiometer and capacitor attached to motor.

Thanks 
Ryan


   

   

Please see attached photos.


Messages In This Thread
41-616 restoration - by 78zenithtv - 10-20-2017, 12:42 AM
RE: 41-616 restoration - by 78zenithtv - 10-20-2017, 08:19 AM
RE: 41-616 restoration - by Ron Ramirez - 10-21-2017, 06:10 AM
RE: 41-616 restoration - by klondike98 - 10-21-2017, 01:00 PM
RE: 41-616 restoration - by 78zenithtv - 10-21-2017, 01:20 PM
RE: 41-616 restoration - by Ron Ramirez - 10-25-2017, 05:10 AM
RE: 41-616 restoration - by 78zenithtv - 10-24-2018, 09:06 AM
RE: 41-616 restoration - by Arran - 10-24-2018, 08:20 PM
RE: 41-616 restoration - by 78zenithtv - 10-28-2018, 04:01 PM
RE: 41-616 restoration - by 78zenithtv - 10-28-2018, 04:02 PM
RE: 41-616 restoration - by klondike98 - 10-29-2018, 09:41 AM
RE: 41-616 restoration - by 78zenithtv - 10-29-2018, 11:58 AM
RE: 41-616 restoration - by Steve Davis - 10-29-2018, 01:23 PM
RE: 41-616 restoration - by klondike98 - 10-29-2018, 03:21 PM
41-616 restoration - by klondike98 - 10-20-2017, 07:24 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>