1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 53-1350 Resistor Overheats
Farmer MM
Junior Member
**
Posts: 8
Threads: 1
Joined: Oct 2017
City: Bismarck, ND
#19

11-03-2017, 08:24 PM
According to my schematics, it is C2.  We already replaced C17 (smaller one below C2).
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 53-1350 Resistor Overheats - by Farmer MM - 10-07-2017, 08:09 PM
RE: Philco 53-1350 Resistor Overheats - by morzh - 10-08-2017, 05:28 PM
RE: Philco 53-1350 Resistor Overheats - by morzh - 10-09-2017, 02:11 PM
RE: Philco 53-1350 Resistor Overheats - by David - 10-09-2017, 05:34 PM
RE: Philco 53-1350 Resistor Overheats - by David - 10-09-2017, 05:37 PM
RE: Philco 53-1350 Resistor Overheats - by David - 10-09-2017, 08:53 PM
RE: Philco 53-1350 Resistor Overheats - by morzh - 10-09-2017, 10:16 PM
RE: Philco 53-1350 Resistor Overheats - by Farmer MM - 11-03-2017, 08:24 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM

[-]
Who's Online
There are currently 7779 online users. [Complete List]
» 1 Member(s) | 7778 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration