1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
48-1270 restoration in progress
Guest
Unregistered
 
#6

03-23-2010, 07:56 PM
I had already taken the chassis and anttana out and restrung the radio dial.





Note from site admin: Sorry, but the photos which were attached to this post are no longer available.
« Next Oldest | Next Newest »


Messages In This Thread
48-1270 restoration in progress - by Guest - 03-16-2010, 03:14 PM
Re: 48-1270 restoration in progress - by planigan - 03-21-2010, 01:43 AM
Re: 48-1270 restoration in progress - by rghines1 - 03-21-2010, 03:49 PM
Re: 48-1270 restoration in progress - by planigan - 03-22-2010, 12:23 AM
Re: 48-1270 restoration in progress - by Guest - 03-23-2010, 07:41 PM
Re: 48-1270 restoration in progress - by Guest - 03-23-2010, 07:56 PM
Re: 48-1270 restoration in progress - by Guest - 03-23-2010, 08:20 PM
Re: 48-1270 restoration in progress - by Guest - 03-23-2010, 08:24 PM
Re: 48-1270 restoration in progress - by Guest - 03-23-2010, 08:36 PM
Re: 48-1270 restoration in progress - by Guest - 03-23-2010, 09:18 PM
Re: 48-1270 restoration in progress - by Guest - 03-24-2010, 09:35 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5912 online users. [Complete List]
» 2 Member(s) | 5910 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration