40-216 restoration questions

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

40-216 restoration questions

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#48

11-08-2017, 08:54 PM

Your probably ok as long as you keep the ends of the HV winding spaced apart a bit. Black for the pri, Green for 6.3v heater, Yellow for the 5v filament, and Red for the hv and red/yellow for the hv center tap.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

40-216 part # 78, filament transformer - by Edisla - 09-26-2017, 11:58 AM

RE: 40-216 restoration questions - by klondike98 - 10-10-2017, 06:53 PM

RE: 40-216 restoration questions - by Edisla - 10-11-2017, 11:24 AM

RE: 40-216 restoration questions - by Mondial - 10-11-2017, 01:19 PM

RE: 40-216 restoration questions - by Edisla - 10-12-2017, 12:29 AM

RE: 40-216 restoration questions - by Warren - 10-12-2017, 01:11 PM

RE: 40-216 restoration questions - by Edisla - 10-12-2017, 05:48 PM

RE: 40-216 restoration questions - by Edisla - 10-23-2017, 08:19 PM

RE: 40-216 restoration questions - by Ron Ramirez - 10-24-2017, 09:38 PM

RE: 40-216 restoration questions - by Edisla - 10-24-2017, 11:06 PM

RE: 40-216 restoration questions - by Edisla - 10-24-2017, 11:07 PM

RE: 40-216 restoration questions - by Arran - 10-25-2017, 04:15 AM

RE: 40-216 restoration questions - by Edisla - 10-25-2017, 07:56 PM

RE: 40-216 restoration questions - by Edisla - 10-27-2017, 01:07 AM

RE: 40-216 restoration questions - by Edisla - 10-31-2017, 09:20 PM

RE: 40-216 restoration questions - by morzh - 10-31-2017, 10:18 PM

RE: 40-216 restoration questions - by Joeztech - 11-01-2017, 04:14 PM

RE: 40-216 restoration questions - by Joeztech - 11-01-2017, 04:41 PM

RE: 40-216 restoration questions - by morzh - 11-01-2017, 04:48 PM

RE: 40-216 restoration questions - by Edisla - 11-03-2017, 09:38 PM

RE: 40-216 restoration questions - by morzh - 11-03-2017, 09:55 PM

RE: 40-216 restoration questions - by Edisla - 11-03-2017, 09:58 PM

RE: 40-216 restoration questions - by morzh - 11-04-2017, 07:45 PM

RE: 40-216 restoration questions - by Edisla - 11-05-2017, 06:32 PM

RE: 40-216 restoration questions - by Edisla - 11-06-2017, 11:40 PM

RE: 40-216 restoration questions - by Edisla - 11-07-2017, 09:07 PM

RE: 40-216 restoration questions - by Radioroslyn - 11-07-2017, 09:38 PM

RE: 40-216 restoration questions - by Edisla - 11-07-2017, 10:16 PM

RE: 40-216 restoration questions - by Edisla - 11-08-2017, 08:45 PM

RE: 40-216 restoration questions - by Radioroslyn - 11-08-2017, 08:54 PM

RE: 40-216 restoration questions - by Edisla - 11-08-2017, 09:30 PM

RE: 40-216 restoration questions - by Edisla - 11-08-2017, 10:33 PM

RE: 40-216 restoration questions - by Edisla - 11-17-2017, 09:14 PM

RE: 40-216 restoration questions - by Edisla - 11-18-2017, 12:12 PM

RE: 40-216 restoration questions - by morzh - 11-18-2017, 12:38 PM

RE: 40-216 restoration questions - by Edisla - 11-27-2017, 11:58 PM

RE: 40-216 restoration questions - by morzh - 11-28-2017, 12:33 AM

RE: 40-216 restoration questions - by Edisla - 11-28-2017, 12:54 AM

RE: 40-216 restoration questions - by Edisla - 12-21-2017, 04:17 PM

RE: 40-216 restoration questions - by Radioroslyn - 12-21-2017, 04:57 PM

RE: 40-216 restoration questions - by Edisla - 12-21-2017, 05:04 PM

RE: 40-216 restoration questions - by Edisla - 12-21-2017, 05:56 PM

RE: 40-216 restoration questions - by morzh - 12-21-2017, 06:30 PM

RE: 40-216 restoration questions - by Edisla - 01-11-2018, 12:28 PM

RE: 40-216 restoration questions - by Ron Ramirez - 01-11-2018, 12:45 PM

RE: 40-216 restoration questions - by morzh - 01-11-2018, 02:25 PM

RE: 40-216 restoration questions - by Radioroslyn - 01-12-2018, 12:32 AM

RE: 40-216 restoration questions - by Edisla - 01-21-2018, 01:20 AM

RE: 40-216 restoration questions - by Radioroslyn - 01-21-2018, 01:27 AM

RE: 40-216 restoration questions - by Edisla - 01-21-2018, 01:36 AM

RE: 40-216 restoration questions - by Edisla - 01-28-2018, 11:03 PM

RE: 40-216 restoration questions - by Edisla - 03-05-2018, 12:43 AM

RE: 40-216 restoration questions - by gregb - 03-05-2018, 04:47 AM

RE: 40-216 restoration questions - by Edisla - 03-05-2018, 01:51 PM

RE: 40-216 part # 78, filament transformer - by klondike98 - 09-26-2017, 04:04 PM

RE: 40-216 part # 78, filament transformer - by Edisla - 09-26-2017, 11:17 PM

40-216 band switch feedback - by Edisla - 09-27-2017, 04:46 PM

RE: 40-216 band switch feedback - by Mondial - 09-27-2017, 10:13 PM

RE: 40-216 band switch feedback - by Edisla - 09-28-2017, 12:47 AM

RE: 40-216 band switch feedback - by Mondial - 09-28-2017, 11:05 PM

RE: 40-216 band switch feedback - by Edisla - 09-29-2017, 10:28 AM

RE: 40-216 band switch feedback - by Edisla - 09-29-2017, 08:39 PM

40-216 5w resistor in place of 2w? - by Edisla - 10-08-2017, 07:41 PM

RE: 40-216 5w resistor in place of 2w? - by morzh - 10-08-2017, 07:46 PM

RE: 40-216 5w resistor in place of 2w? - by Edisla - 10-10-2017, 12:05 AM

RE: 40-216 5w resistor in place of 2w? - by morzh - 10-10-2017, 09:14 AM

RE: 40-216 5w resistor in place of 2w? - by Edisla - 10-10-2017, 11:02 AM

RE: 40-216 5w resistor in place of 2w? - by morzh - 10-10-2017, 11:10 AM

RE: 40-216 5w resistor in place of 2w? - by Radioroslyn - 10-10-2017, 11:19 AM

RE: 40-216 5w resistor in place of 2w? - by Raleigh - 10-10-2017, 01:33 PM

RE: 40-216 5w resistor in place of 2w? - by morzh - 10-10-2017, 01:55 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online

There are currently 5227 online users. [Complete List]
» 2 Member(s) | 5225 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me