1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Output transformer
EdHolland
Phorum Expert
*****
Posts: 1,287
Threads: 44
Joined: Nov 2017
City: Menlo Park State, Province, Country: CA
#15

11-28-2017, 03:05 PM
I am have been using high quality tracing paper for interleaf paper.

https://www.amazon.com/gp/product/B000KN...UTF8&psc=1

It cuts and handles nicely, and is very close to the thickness (measured) of the original paper.
I don't hold with furniture that talks.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Output transformer - by rfeenstra - 11-11-2017, 01:58 PM
RE: Output transformer - by klondike98 - 11-11-2017, 02:10 PM
RE: Output transformer - by Radioroslyn - 11-11-2017, 02:51 PM
RE: Output transformer - by rfeenstra - 11-11-2017, 05:15 PM
RE: Output transformer - by rfeenstra - 11-11-2017, 05:32 PM
RE: Output transformer - by Radioroslyn - 11-11-2017, 08:49 PM
RE: Output transformer - by rfeenstra - 11-12-2017, 05:07 AM
RE: Output transformer - by Radioroslyn - 11-12-2017, 11:22 AM
RE: Output transformer - by Steve Davis - 11-12-2017, 12:30 PM
RE: Output transformer - by rfeenstra - 11-12-2017, 01:03 PM
RE: Output transformer - by rfeenstra - 11-12-2017, 01:16 PM
RE: Output transformer - by Steve Davis - 11-13-2017, 12:20 AM
RE: Output transformer - by rfeenstra - 11-19-2017, 12:56 AM
RE: Output transformer - by rfeenstra - 11-25-2017, 10:37 PM
RE: Output transformer - by EdHolland - 11-28-2017, 03:05 PM
RE: Output transformer - by rfeenstra - 11-28-2017, 05:01 PM
RE: Output transformer - by EdHolland - 11-28-2017, 05:12 PM
RE: Output transformer - by rfeenstra - 11-28-2017, 06:50 PM
RE: Output transformer - by rfeenstra - 11-28-2017, 07:04 PM
RE: Output transformer - by EdHolland - 11-28-2017, 08:14 PM
RE: Output transformer - by rfeenstra - 11-28-2017, 11:00 PM
RE: Output transformer - by rfeenstra - 12-08-2017, 06:20 PM
RE: Output transformer - by klondike98 - 12-08-2017, 07:21 PM
RE: Output transformer - by Kenneth F. Besso Jr. - 12-08-2017, 09:26 PM
RE: Output transformer - by rfeenstra - 12-09-2017, 01:30 AM
RE: Output transformer - by Arran - 12-09-2017, 04:09 AM
RE: Output transformer - by Ron Ramirez - 12-09-2017, 08:42 AM
RE: Output transformer - by rfeenstra - 12-09-2017, 10:59 AM
RE: Output transformer - by EdHolland - 12-11-2017, 05:46 PM
RE: Output transformer - by tbone - 12-11-2017, 07:34 PM
RE: Output transformer - by rfeenstra - 12-12-2017, 12:42 AM
RE: Output transformer - by EdHolland - 12-12-2017, 01:33 PM



Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 5244 online users. [Complete List]
» 1 Member(s) | 5243 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration