Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

A Jackson Bell model ????
#15

You can't really go by the dial scales as a means of identifying many of these mid 1930s "Pee Wee" sets, the dials were often generic off the shelf scales. Sometimes you can identify the set by the tube lineup and it's location, and whether the set has a power transformer, a curtain burner cord, or a ballast tube. That last set has a power transformer, and one IF can, so that narrows it down, the cabinet might help too since it appears that the top and sides are made out of solid lumber that was molded with a shaper.
Regards
Arran


Messages In This Thread
A Jackson Bell model ???? - by Scott D - 09-19-2017, 08:51 PM
RE: A Jackson Bell model ???? - by Phlogiston - 09-19-2017, 09:07 PM
RE: A Jackson Bell model ???? - by morzh - 09-19-2017, 09:41 PM
RE: A Jackson Bell model ???? - by Arran - 09-19-2017, 09:41 PM
RE: A Jackson Bell model ???? - by Scott D - 09-19-2017, 10:24 PM
RE: A Jackson Bell model ???? - by Scott D - 09-19-2017, 10:30 PM
RE: A Jackson Bell model ???? - by OldRestorer - 09-20-2017, 08:00 AM
RE: A Jackson Bell model ???? - by Scott D - 09-20-2017, 08:52 AM
RE: A Jackson Bell model ???? - by morzh - 09-20-2017, 10:30 AM
RE: A Jackson Bell model ???? - by Scott D - 09-20-2017, 05:15 PM
RE: A Jackson Bell model ???? - by WallaceRoger - 09-21-2017, 11:59 AM
RE: A Jackson Bell model ???? - by kc5gym - 09-21-2017, 06:36 PM
RE: A Jackson Bell model ???? - by OldRestorer - 09-22-2017, 09:24 AM
RE: A Jackson Bell model ???? - by Scott D - 11-30-2017, 04:38 PM
RE: A Jackson Bell model ???? - by Arran - 11-30-2017, 11:22 PM
RE: A Jackson Bell model ???? - by palegreenthumb - 12-02-2017, 12:55 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4099 online users. [Complete List]
» 2 Member(s) | 4097 Guest(s)
AvatarAvatar

>