Model 70

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Model 70

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

12-03-2017, 11:23 AM

Next Question Since this uses Electrolytic caps can they be replaced with 10UF Caps.Originals are 6 UF

Skip..

Or I have some 4.7 Electrolytic caps Can I add a Non electrolytic cap at 2.2 UF to come up with 6.9UF would that work?

Skip...

Find

« Next Oldest | Next Newest »

Messages In This Thread

Model 70 - by vecher - 11-29-2017, 09:41 PM

RE: Model 70 - by Ron Ramirez - 11-29-2017, 10:33 PM

RE: Model 70 - by vecher - 12-02-2017, 01:55 AM

RE: Model 70 - by Arran - 12-02-2017, 03:46 AM

RE: Model 70 - by Steve Davis - 12-02-2017, 08:53 AM

RE: Model 70 - by vecher - 12-02-2017, 02:30 PM

RE: Model 70 - by vecher - 12-02-2017, 04:40 PM

RE: Model 70 - by vecher - 12-03-2017, 11:23 AM

RE: Model 70 - by morzh - 12-03-2017, 12:20 PM

RE: Model 70 - by vecher - 12-25-2017, 12:40 AM

RE: Model 70 - by AudreyHepburn - 12-29-2017, 11:14 PM

RE: Model 70 - by vecher - 12-29-2017, 11:59 PM

RE: Model 70 - by Radioroslyn - 12-30-2017, 12:36 AM

RE: Model 70 - by TV MAN - 12-30-2017, 11:30 PM

RE: Model 70 - by vecher - 12-31-2017, 02:19 AM

RE: Model 70 - by vecher - 01-07-2018, 12:17 AM

RE: Model 70 - by klondike98 - 01-07-2018, 09:16 AM

RE: Model 70 - by Steve Davis - 01-07-2018, 10:46 AM

RE: Model 70 - by Ron Ramirez - 01-07-2018, 10:52 AM

RE: Model 70 - by vecher - 01-07-2018, 12:53 PM

RE: Model 70 - by vecher - 01-10-2018, 12:15 PM

RE: Model 70 - by Steve Davis - 01-10-2018, 12:36 PM

RE: Model 70 - by klondike98 - 01-10-2018, 01:07 PM

RE: Model 70 - by vecher - 01-10-2018, 02:08 PM

RE: Model 70 - by morzh - 01-10-2018, 05:05 PM

RE: Model 70 - by klondike98 - 01-10-2018, 06:25 PM

RE: Model 70 - by Warren - 01-10-2018, 09:17 PM

RE: Model 70 - by vecher - 01-11-2018, 12:59 AM

RE: Model 70 - by vecher - 01-11-2018, 01:12 AM

RE: Model 70 - by Steve Davis - 01-11-2018, 02:00 AM

RE: Model 70 - by morzh - 01-11-2018, 09:36 AM

RE: Model 70 - by vecher - 01-13-2018, 08:18 PM

RE: Model 70 - by vecher - 01-13-2018, 08:21 PM

RE: Model 70 - by vecher - 01-17-2018, 12:13 AM

RE: Model 70 - by vecher - 01-20-2018, 09:17 PM

RE: Model 70 - by Steve Davis - 01-21-2018, 12:07 AM

RE: Model 70 - by EdHolland - 01-21-2018, 03:33 AM

RE: Model 70 - by Steve D - 01-21-2018, 11:49 AM

RE: Model 70 - by vecher - 01-21-2018, 02:22 PM

RE: Model 70 - by vecher - 01-21-2018, 06:02 PM

RE: Model 70 - by vecher - 01-22-2018, 12:02 AM

RE: Model 70 - by vecher - 01-22-2018, 09:47 PM

RE: Model 70 - by vecher - 01-28-2018, 11:25 PM

RE: Model 70 - by mg34.42 - 03-18-2018, 03:32 PM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me