reduce voltage

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

reduce voltage

denver
Member

Posts: 217
Threads: 40
Joined: Dec 2009

#15

04-06-2010, 03:22 PM

hi I figured out why voltage running high when i checked. Wasn,t hooking speaker up Icon_redface

Hard set to work on big console big speaker.
Ihave it playing fine picks up good for about 20 min . Then fades out let cool off then plays 20 min again .
I replaced every cap resistors and bad tubes . Only things i did not are the micas what do you think.
If i did which ones .
Thanks Kent. Icon_rolleyes

Find

« Next Oldest | Next Newest »

Messages In This Thread

reduce voltage - by denver - 03-17-2010, 01:12 PM

Re: reduce voltage - by rghines1 - 03-17-2010, 04:41 PM

Re: reduce voltage - by denver - 03-17-2010, 04:50 PM

Re: reduce voltage - by denver - 03-17-2010, 04:54 PM

Re: reduce voltage - by rghines1 - 03-17-2010, 07:09 PM

Re: reduce voltage - by denver - 03-17-2010, 07:22 PM

Re: reduce voltage - by Ron Ramirez - 03-17-2010, 07:37 PM

Re: reduce voltage - by denver - 03-17-2010, 08:39 PM

Re: reduce voltage - by Carl Travis - 03-17-2010, 08:44 PM

Re: reduce voltage - by rghines1 - 03-18-2010, 07:13 AM

Re: reduce voltage - by denver - 03-18-2010, 12:58 PM

Re: reduce voltage - by rghines1 - 03-18-2010, 05:37 PM

Re: reduce voltage - by denver - 03-18-2010, 06:37 PM

Re: reduce voltage - by denver - 03-21-2010, 06:04 PM

Re: reduce voltage - by denver - 04-06-2010, 03:22 PM

Re: reduce voltage - by Ron Ramirez - 04-06-2010, 04:05 PM

Re: reduce voltage - by rghines1 - 04-07-2010, 08:28 AM

Re: reduce voltage - by codefox1 - 04-07-2010, 10:27 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

Who's Online

There are currently 2353 online users. [Complete List]
» 2 Member(s) | 2351 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me