Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-1 code 121A
#39

Well, tomorrow I should be getting final electrical components in the mail. Just tying up loose ends on this unit before final assembly. Something that I've been putting off are the speaker connections... The plug connection from the chassis has only one wire connected to it, and is going to candohm #3320 (this set has 3 separate candohm units), as the other three wires were pulled out of their socket holes at the speaker when I got the radio. I've poured over the schematics, and every time I think I have it, I get an overwhelming feeling of doubt. On the speaker socket, (4 pin connector, 5 wires), with the 2 wide spaced pins on the bottom and the 2 narrow spaced on top, the one wire that is connected from candohm goes to the top left of speaker connection (Narrow section- this has 2 wires at the pin- one to the output transformer, the other to the voice coil). The other wires: one goes to 6f6, another to the next 6f6, and the last goes to #3282 candohm. How shall I attach these wires correctly. Should be a piece of cake, I know, (and I've got a good idea how they should go), but I need verification. THANKS

Jim


Messages In This Thread
38-1 code 121A - by Electrothaumaturgist - 09-28-2017, 01:37 AM
RE: 38-1 code 121A - by Radioroslyn - 09-28-2017, 03:29 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 09-28-2017, 04:01 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 10-28-2017, 03:39 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 10-28-2017, 03:51 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 10-28-2017, 04:13 PM
RE: 38-1 code 121A - by morzh - 10-28-2017, 05:04 PM
RE: 38-1 code 121A - by Radioroslyn - 10-28-2017, 05:12 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 10-28-2017, 06:16 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-08-2017, 01:33 AM
RE: 38-1 code 121A - by Radioroslyn - 11-08-2017, 12:50 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-08-2017, 11:05 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-08-2017, 11:10 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-08-2017, 11:18 PM
RE: 38-1 code 121A - by Radioroslyn - 11-08-2017, 11:25 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-08-2017, 11:35 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-08-2017, 11:38 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-11-2017, 05:33 AM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-18-2017, 03:21 AM
RE: 38-1 code 121A - by Ron Ramirez - 11-18-2017, 09:05 AM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-18-2017, 11:17 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-25-2017, 12:45 AM
RE: 38-1 code 121A - by Radioroslyn - 11-25-2017, 11:42 AM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-25-2017, 04:35 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-28-2017, 03:02 AM
RE: 38-1 code 121A - by Radioroslyn - 11-28-2017, 01:27 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-28-2017, 01:31 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-28-2017, 01:44 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-28-2017, 02:03 PM
RE: 38-1 code 121A - by Radioroslyn - 11-28-2017, 02:47 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-28-2017, 08:33 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 11-29-2017, 11:13 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 12-03-2017, 07:55 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 12-04-2017, 05:53 PM
RE: 38-1 code 121A - by Radioroslyn - 12-04-2017, 07:38 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 12-04-2017, 08:35 PM
RE: 38-1 code 121A - by Radioroslyn - 12-04-2017, 08:52 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 12-04-2017, 10:13 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 12-16-2017, 01:20 AM
RE: 38-1 code 121A - by Electrothaumaturgist - 12-16-2017, 06:48 AM
RE: 38-1 code 121A - by Electrothaumaturgist - 12-25-2017, 04:42 PM
RE: 38-1 code 121A - by EdHolland - 12-26-2017, 10:45 PM
RE: 38-1 code 121A - by Electrothaumaturgist - 12-27-2017, 07:16 PM



Users browsing this thread: 9 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 5207 online users. [Complete List]
» 1 Member(s) | 5206 Guest(s)
Avatar

>