1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Mysterios Model 650RX(?) chairside
Nathan Slingerland
Super Moderator
******
Posts: 1,874
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#9

12-16-2017, 03:06 AM
Very interesting.

Other folks have seen a lot more Philcos than me but I'll throw one more data point out there: By coincidence I've been putting together a scan of the 1936 Philco catalog that I'll post once it's all cleaned up. Here's are the raw scans of the pages pertaining to the 650 based models:

https://drive.google.com/file/d/1-2g1s52...sp=sharing

FWIW, it doesn't mention a single piece variant for the 650RX.

Ron - what do you think?
Are there separate production numbers for the speaker and radio cabinets of the 650RX?
Find
« Next Oldest | Next Newest »


Messages In This Thread
Mysterios Model 650RX(?) chairside - by Diverted - 12-14-2017, 06:02 PM
RE: Mysterios Model 650RX(?) chairside - by Nathan Slingerland - 12-16-2017, 03:06 AM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4885 online users. [Complete List]
» 2 Member(s) | 4883 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios