condenser/resistor question?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

condenser/resistor question?

tab10672
Senior Member

Posts: 411
Threads: 42
Joined: Sep 2008
City: Ironton Ohio

#1

05-11-2010, 07:52 PM

I am about to recap a mod. 511, what wattage should the wound resistors coupled to the (3) .1 uf /100ohm by pass condensers be repaced with after I remove and repace the .1uf half of the condenser?? I am attempting to rebuild the original part, (if possible) but if the resistor is larger than 1/2 watt I dont think there is enough room. Any input would be greatly appriciated. Thanks

Find

« Next Oldest | Next Newest »

Messages In This Thread

condenser/resistor question? - by tab10672 - 05-11-2010, 07:52 PM

Re: condenser/resistor question? - by hotrod - 05-11-2010, 08:43 PM

Re: condenser/resistor question? - by tab10672 - 05-11-2010, 09:18 PM

Re: condenser/resistor question? - by hotrod - 05-12-2010, 10:19 PM

Re: condenser/resistor question? - by exray - 05-13-2010, 07:10 AM

Re: condenser/resistor question? - by tab10672 - 05-13-2010, 04:21 PM

Re: condenser/resistor question? - by exray - 05-13-2010, 05:30 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5096 online users. [Complete List]
» 1 Member(s) | 5095 Guest(s)