Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

PT-25 audio distortion
#13

Update.  Replaced resistor #'s from the schematic #12 (2.2meg), #14(22k), #20(470k) and #21(130ohms)
Also found a .012 cap from previously replaced and should be a .01mfd
Resistor #18  (220k) tested at 223k
Audio is better but still distorted. 
Attached pic of electronic cleaner I had been using.


Messages In This Thread
PT-25 audio distortion - by WyTex - 12-19-2017, 12:45 PM
RE: PT-25 audio distortion - by morzh - 12-19-2017, 02:29 PM
RE: PT-25 audio distortion - by David - 12-19-2017, 04:08 PM
RE: PT-25 audio distortion - by WyTex - 12-19-2017, 04:09 PM
RE: PT-25 audio distortion - by Phlogiston - 12-19-2017, 04:37 PM
RE: PT-25 audio distortion - by morzh - 12-19-2017, 11:02 PM
RE: PT-25 audio distortion - by WyTex - 12-20-2017, 10:06 AM
RE: PT-25 audio distortion - by Steve Davis - 12-20-2017, 11:34 AM
RE: PT-25 audio distortion - by Phlogiston - 12-20-2017, 11:52 AM
RE: PT-25 audio distortion - by klondike98 - 12-20-2017, 12:01 PM
RE: PT-25 audio distortion - by Phlogiston - 12-20-2017, 03:28 PM
RE: PT-25 audio distortion - by klondike98 - 12-20-2017, 05:45 PM
RE: PT-25 audio distortion - by WyTex - 12-20-2017, 06:16 PM
RE: PT-25 audio distortion - by morzh - 12-20-2017, 06:46 PM
RE: PT-25 audio distortion - by klondike98 - 12-20-2017, 06:48 PM
RE: PT-25 audio distortion - by Arran - 12-21-2017, 01:52 AM
RE: PT-25 audio distortion - by morzh - 12-21-2017, 10:32 AM
RE: PT-25 audio distortion - by WyTex - 12-21-2017, 10:58 AM
RE: PT-25 audio distortion - by Phlogiston - 12-21-2017, 12:05 PM
RE: PT-25 audio distortion - by Radioroslyn - 12-21-2017, 12:33 PM
RE: PT-25 audio distortion - by morzh - 12-21-2017, 01:14 PM
RE: PT-25 audio distortion - by WyTex - 01-05-2018, 02:26 PM
RE: PT-25 audio distortion - by morzh - 01-05-2018, 06:09 PM



Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Looking at the pic supplied by Rod B, you can duplicate the missing loop antenna. 10 gauge copper wire can be used to m...MrFixr55 — 01:20 AM
Philco 46-480 Electronic Restoration
I’m making progress with the alignment. It was a combination of needing to solder the connection on pin 3 of the BC osci...jrblasde — 10:21 PM
Philco 46-480 Electronic Restoration
Mr. Fixr Compared to you I am sooo green behibd the ears...I have about 40 or so sets.morzh — 07:12 PM
48-482 rear panel help
Many thanks to all for the responses! No plastic button "covers" on my radio. Ron, thanks for the chapter on...keithchip — 05:53 PM
Philco 42-345 Restoration/Repair
I am back to working on this radio and managed to get a couple of radio stations to come in. But can someone help me to ...osanders0311 — 01:58 PM
48-482 rear panel help
Hi Kettlechip and welcom to the Phorum. The back panel question is interesting. I have quite a few radios that use pow...MrFixr55 — 08:24 AM
Philco 46-480 Electronic Restoration
Not too much at all! :lol:  Sounds like you’re just dabbling into the hobby!jrblasde — 07:56 AM
Philco 46-480 Electronic Restoration
Hi Joseph, Fortunately, Ms. Fixr does not read my computer, or she would warn you against coming to me for sanity ch...MrFixr55 — 07:27 AM
48-482 rear panel help
There's a picture of one of the plastic covers in the following thread: I bought a full set of them in 2012 or so fro...klondike98 — 11:15 PM
Philco 46-480 Electronic Restoration
Good sanity check! You are correct—the first (as in, the most counterclockwise) position is for the push button presets....jrblasde — 11:05 PM

[-]
Who's Online
There are currently 646 online users. [Complete List]
» 1 Member(s) | 645 Guest(s)
Avatar

>