Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Arvin 442 cap question
#3

Hi Brian and Merry Christmas,
Good practice would dictate that C-10 should be 50mf or less. If C-10 is a high value it can damage to cathode of the 35Z5 thru excessive current during warmup. R-11 helps limit the current. C-11 isn't critical, typically they are 30mf but you can go a bit large for better filtering like 47mf. C-12 is normally 10-20mf @ 20-35v. 100mf was probably meant for a portable set to filter the filament circuit. A bit overkill for the cathode bypass.
If you want to get something that looks somewhat correct https://www.tubesandmore.com/products/ca...0v-22-f25v  or replacing them with single units.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Arvin 442 cap question - by Foose - 12-25-2017, 12:18 PM
RE: Arvin 442 cap question - by Phlogiston - 12-25-2017, 01:10 PM
RE: Arvin 442 cap question - by Radioroslyn - 12-25-2017, 01:10 PM
RE: Arvin 442 cap question - by Foose - 12-25-2017, 04:13 PM
RE: Arvin 442 cap question - by Radioroslyn - 12-25-2017, 05:33 PM
RE: Arvin 442 cap question - by Phlogiston - 12-25-2017, 06:18 PM
RE: Arvin 442 cap question - by Arran - 12-25-2017, 10:56 PM
RE: Arvin 442 cap question - by Foose - 12-27-2017, 04:37 PM
RE: Arvin 442 cap question - by Radioroslyn - 12-27-2017, 07:35 PM
RE: Arvin 442 cap question - by Foose - 12-28-2017, 04:07 PM
RE: Arvin 442 cap question - by Foose - 12-30-2017, 07:03 PM
RE: Arvin 442 cap question - by Radioroslyn - 12-31-2017, 12:39 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>