1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
38-690 Refinish June Update
tbone
Senior Member
****
Posts: 278
Threads: 19
Joined: Nov 2016
City: Cromwell State, Province, Country: CT
#4

12-28-2017, 08:14 PM
Ok that makes sense. I think it was around 1940 when they used photo finish quite a bit.

Thank you.

This is going to be quite a job, but I should be able to use a citrus stripper to do this in sections. The hardest part will be the roll top which is on canvas. Not sure about that yet.
Find
« Next Oldest | Next Newest »


Messages In This Thread
38-690 Refinish June Update - by tbone - 12-28-2017, 08:04 PM
RE: 38-690 wood and is there photofinish? - by tbone - 12-28-2017, 08:14 PM
RE: 38-690 Refinish has begun - by tbone - 03-03-2018, 08:33 AM
RE: 38-690 Refinish has begun - by Phlogiston - 03-03-2018, 11:46 AM
RE: 38-690 Refinish has begun - by tbone - 03-03-2018, 12:59 PM
RE: 38-690 Refinish has begun - by Phlogiston - 03-03-2018, 05:08 PM
RE: 38-690 Refinish has begun - by tbone - 03-03-2018, 08:55 PM
RE: 38-690 Refinish has begun - by tbone - 03-04-2018, 05:04 PM
RE: 38-690 Refinish has begun - by Arran - 03-04-2018, 06:07 PM
RE: 38-690 Refinish has begun - by Phlogiston - 03-04-2018, 08:04 PM
RE: 38-690 Refinish has begun - by tbone - 03-25-2018, 06:26 PM
RE: 38-690 Refinish has begun - by OldRestorer - 03-25-2018, 08:41 PM
RE: 38-690 Refinish has begun - by Ron Ramirez - 03-25-2018, 10:17 PM
RE: 38-690 Refinish has begun - by morzh - 03-25-2018, 11:22 PM
RE: 38-690 Refinish has begun - by WyTex - 03-26-2018, 06:38 AM
RE: 38-690 Refinish has begun - by tbone - 03-26-2018, 12:17 PM
RE: 38-690 Refinish has begun - by tbone - 05-05-2018, 08:31 AM
RE: 38-690 Refinish has begun - by Ron Ramirez - 05-05-2018, 09:40 AM
RE: 38-690 Refinish has begun - by Phlogiston - 05-05-2018, 10:38 AM
RE: 38-690 Refinish has begun - by tbone - 05-05-2018, 02:50 PM
RE: 38-690 Refinish has begun - by Phlogiston - 05-05-2018, 07:51 PM
RE: 38-690 Refinish has begun - by OldRestorer - 05-10-2018, 09:01 AM
RE: 38-690 Refinish has begu - by tbone - 05-10-2018, 05:32 PM
RE: 38-690 Refinish has begun - by OldRestorer - 05-10-2018, 07:52 PM
RE: 38-690 Refinish has begun - by morzh - 05-10-2018, 08:40 PM
RE: 38-690 Refinish has begun - by tbone - 05-12-2018, 09:35 AM
RE: 38-690 Refinish June Update - by tbone - 06-03-2018, 07:08 PM
RE: 38-690 Refinish June Update - by morzh - 06-03-2018, 09:10 PM
RE: 38-690 Refinish June Update - by PhilcoJohn - 06-05-2018, 07:52 AM
RE: 38-690 Refinish June Update - by EdHolland - 06-06-2018, 03:49 PM
RE: 38-690 Refinish June Update - by Greggshere - 09-29-2018, 08:40 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6364 online users. [Complete List]
» 1 Member(s) | 6363 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration