1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
38-690 Refinish June Update
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#7

12-28-2017, 10:38 PM
Midway thru 1936 ('37 model year) and there after was BIG on the Philcocoat (photo) finish.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
38-690 Refinish June Update - by tbone - 12-28-2017, 08:04 PM
RE: 38-690 wood and is there photofinish? - by Radioroslyn - 12-28-2017, 10:38 PM
RE: 38-690 Refinish has begun - by tbone - 03-03-2018, 08:33 AM
RE: 38-690 Refinish has begun - by Phlogiston - 03-03-2018, 11:46 AM
RE: 38-690 Refinish has begun - by tbone - 03-03-2018, 12:59 PM
RE: 38-690 Refinish has begun - by Phlogiston - 03-03-2018, 05:08 PM
RE: 38-690 Refinish has begun - by tbone - 03-03-2018, 08:55 PM
RE: 38-690 Refinish has begun - by tbone - 03-04-2018, 05:04 PM
RE: 38-690 Refinish has begun - by Arran - 03-04-2018, 06:07 PM
RE: 38-690 Refinish has begun - by Phlogiston - 03-04-2018, 08:04 PM
RE: 38-690 Refinish has begun - by tbone - 03-25-2018, 06:26 PM
RE: 38-690 Refinish has begun - by OldRestorer - 03-25-2018, 08:41 PM
RE: 38-690 Refinish has begun - by Ron Ramirez - 03-25-2018, 10:17 PM
RE: 38-690 Refinish has begun - by morzh - 03-25-2018, 11:22 PM
RE: 38-690 Refinish has begun - by WyTex - 03-26-2018, 06:38 AM
RE: 38-690 Refinish has begun - by tbone - 03-26-2018, 12:17 PM
RE: 38-690 Refinish has begun - by tbone - 05-05-2018, 08:31 AM
RE: 38-690 Refinish has begun - by Ron Ramirez - 05-05-2018, 09:40 AM
RE: 38-690 Refinish has begun - by Phlogiston - 05-05-2018, 10:38 AM
RE: 38-690 Refinish has begun - by tbone - 05-05-2018, 02:50 PM
RE: 38-690 Refinish has begun - by Phlogiston - 05-05-2018, 07:51 PM
RE: 38-690 Refinish has begun - by OldRestorer - 05-10-2018, 09:01 AM
RE: 38-690 Refinish has begu - by tbone - 05-10-2018, 05:32 PM
RE: 38-690 Refinish has begun - by OldRestorer - 05-10-2018, 07:52 PM
RE: 38-690 Refinish has begun - by morzh - 05-10-2018, 08:40 PM
RE: 38-690 Refinish has begun - by tbone - 05-12-2018, 09:35 AM
RE: 38-690 Refinish June Update - by tbone - 06-03-2018, 07:08 PM
RE: 38-690 Refinish June Update - by morzh - 06-03-2018, 09:10 PM
RE: 38-690 Refinish June Update - by PhilcoJohn - 06-05-2018, 07:52 AM
RE: 38-690 Refinish June Update - by EdHolland - 06-06-2018, 03:49 PM
RE: 38-690 Refinish June Update - by Greggshere - 09-29-2018, 08:40 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration