1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Tube tester repair TV-11
kd4pqf
Junior Member
**
Posts: 14
Threads: 7
Joined: Mar 2010
#3

05-23-2010, 04:48 PM
I thought about that but most of them are way high or way low. thought about replacing the rheostat . but it seems to work ok maybe a little jumpy...but it has fried two tubes form the voltage being so high
Find
« Next Oldest | Next Newest »


Messages In This Thread
Tube tester repair TV-11 - by kd4pqf - 05-20-2010, 04:21 PM
Re: Tube tester repair TV-11 - by Alan Douglas - 05-20-2010, 09:00 PM
Re: Tube tester repair TV-11 - by kd4pqf - 05-23-2010, 04:48 PM
Re: Tube tester repair TV-11 - by DCASAZZA - 05-23-2010, 07:57 PM
Re: Tube tester repair TV-11 - by Alan Douglas - 05-23-2010, 09:46 PM
Re: Tube tester repair TV-11 - by kd4pqf - 05-25-2010, 10:32 PM
Re: Tube tester repair TV-11 - by Jim Berg - 05-26-2010, 09:44 PM
Re: Tube tester repair TV-11 - by Alan Douglas - 05-26-2010, 09:47 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios