6L6G vs 6L6GA

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

6L6G vs 6L6GA

Radioroslyn
Phorum Expert

Posts: 7,297
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

01-17-2018, 04:01 PM

Yes. The 6L6GA and 6L6G are the same, the 6L6GB has a bit better specs as it can handle higher plate voltage and dissapation. Using a 6L6G where a 6L6GBwas used may not be a great idea depending on the circuit and voltages used.
You may find that the 6L6G is a bit taller than the GA.

GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

(This post was last modified: 01-17-2018, 04:14 PM by Radioroslyn.)

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

6L6G vs 6L6GA - by WyTex - 01-17-2018, 03:25 PM

RE: 6L6G vs 6L6GA - by morzh - 01-17-2018, 03:41 PM

RE: 6L6G vs 6L6GA - by Radioroslyn - 01-17-2018, 04:01 PM

RE: 6L6G vs 6L6GA - by jcassity - 01-17-2018, 05:35 PM

RE: 6L6G vs 6L6GA - by Arran - 01-18-2018, 02:34 AM

RE: 6L6G vs 6L6GA - by WyTex - 01-18-2018, 06:45 AM

RE: 6L6G vs 6L6GA - by Arran - 01-19-2018, 12:49 AM

RE: 6L6G vs 6L6GA - by Ron Ramirez - 01-19-2018, 07:10 AM

RE: 6L6G vs 6L6GA - by WyTex - 01-19-2018, 12:36 PM

RE: 6L6G vs 6L6GA - by WyTex - 01-19-2018, 12:45 PM

RE: 6L6G vs 6L6GA - by Ron Ramirez - 01-19-2018, 01:36 PM

RE: 6L6G vs 6L6GA - by David - 01-19-2018, 03:51 PM

RE: 6L6G vs 6L6GA - by WyTex - 01-19-2018, 04:54 PM

RE: 6L6G vs 6L6GA - by Ron Ramirez - 01-19-2018, 07:07 PM

RE: 6L6G vs 6L6GA - by WyTex - 01-21-2018, 05:21 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Need Help to ID this radio 11 tube Philco
Welcome to the Phorum, Ken! Lots of help here for all of your restoration questions. Take care and BE HEALTHY! - Gar...GarySP — 07:59 PM
Need Help to ID this radio 11 tube Philco
Thank you. I went to your online library and found 2 schematics. I will download and compare to components!Ken D. — 06:31 PM
Need Help to ID this radio 11 tube Philco
It is a 16B tombstone.morzh — 06:13 PM
Zenith H725
David - sorry, I reread your post and finally saw THD - now the % figures make sense. Thanks for explaining. The PSU...EdHolland — 06:06 PM
Need Help to ID this radio 11 tube Philco
Hi Everyone, New member but have been reading this for awhile for tips! Vaccum tubes were before my time so bear with ...Ken D. — 06:03 PM
My Philco 37-116 Restore
Thank you MrFixR55, I appreciate your comments very much. I do not detect much hum if any so I will be staying with the ...dconant — 05:15 PM
My Philco 37-116 Restore
Hi DConant Yes, you can replace chokes with resistors. You do stand the risk of increased hum. the solution is to inc...MrFixr55 — 04:23 PM
Zenith H725
1.7-3.9 %, a modified Sine wave inverter is around 25%. Most generators from big box stores run 10% at a 50% load. What ...David — 04:06 PM
My Philco 37-116 Restore
I am having a heck of a time doing the alignment on the AM band. I can't seem to dial in the 1500 KC oscillator. I can h...dconant — 03:35 PM
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM

Who's Online

There are currently 721 online users. [Complete List]
» 2 Member(s) | 719 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me