Model 70

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Model 70

Steve Davis
Phorum Expert

Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO

#36

01-21-2018, 12:07 AM

Skip, you need some sort of a stop on your drill bit, either a collar or a piece of tubing slipped over the bit that will not let the bit go through and puncture the cone. The only other safe way, would be to remove the cone.

Steve

M R Radios C M Tubes

Find

« Next Oldest | Next Newest »

Messages In This Thread

Model 70 - by vecher - 11-29-2017, 09:41 PM

RE: Model 70 - by Ron Ramirez - 11-29-2017, 10:33 PM

RE: Model 70 - by vecher - 12-02-2017, 01:55 AM

RE: Model 70 - by Arran - 12-02-2017, 03:46 AM

RE: Model 70 - by Steve Davis - 12-02-2017, 08:53 AM

RE: Model 70 - by vecher - 12-02-2017, 02:30 PM

RE: Model 70 - by vecher - 12-02-2017, 04:40 PM

RE: Model 70 - by vecher - 12-03-2017, 11:23 AM

RE: Model 70 - by morzh - 12-03-2017, 12:20 PM

RE: Model 70 - by vecher - 12-25-2017, 12:40 AM

RE: Model 70 - by AudreyHepburn - 12-29-2017, 11:14 PM

RE: Model 70 - by vecher - 12-29-2017, 11:59 PM

RE: Model 70 - by Radioroslyn - 12-30-2017, 12:36 AM

RE: Model 70 - by TV MAN - 12-30-2017, 11:30 PM

RE: Model 70 - by vecher - 12-31-2017, 02:19 AM

RE: Model 70 - by vecher - 01-07-2018, 12:17 AM

RE: Model 70 - by klondike98 - 01-07-2018, 09:16 AM

RE: Model 70 - by Steve Davis - 01-07-2018, 10:46 AM

RE: Model 70 - by Ron Ramirez - 01-07-2018, 10:52 AM

RE: Model 70 - by vecher - 01-07-2018, 12:53 PM

RE: Model 70 - by vecher - 01-10-2018, 12:15 PM

RE: Model 70 - by Steve Davis - 01-10-2018, 12:36 PM

RE: Model 70 - by klondike98 - 01-10-2018, 01:07 PM

RE: Model 70 - by vecher - 01-10-2018, 02:08 PM

RE: Model 70 - by morzh - 01-10-2018, 05:05 PM

RE: Model 70 - by klondike98 - 01-10-2018, 06:25 PM

RE: Model 70 - by Warren - 01-10-2018, 09:17 PM

RE: Model 70 - by vecher - 01-11-2018, 12:59 AM

RE: Model 70 - by vecher - 01-11-2018, 01:12 AM

RE: Model 70 - by Steve Davis - 01-11-2018, 02:00 AM

RE: Model 70 - by morzh - 01-11-2018, 09:36 AM

RE: Model 70 - by vecher - 01-13-2018, 08:18 PM

RE: Model 70 - by vecher - 01-13-2018, 08:21 PM

RE: Model 70 - by vecher - 01-17-2018, 12:13 AM

RE: Model 70 - by vecher - 01-20-2018, 09:17 PM

RE: Model 70 - by Steve Davis - 01-21-2018, 12:07 AM

RE: Model 70 - by EdHolland - 01-21-2018, 03:33 AM

RE: Model 70 - by Steve D - 01-21-2018, 11:49 AM

RE: Model 70 - by vecher - 01-21-2018, 02:22 PM

RE: Model 70 - by vecher - 01-21-2018, 06:02 PM

RE: Model 70 - by vecher - 01-22-2018, 12:02 AM

RE: Model 70 - by vecher - 01-22-2018, 09:47 PM

RE: Model 70 - by vecher - 01-28-2018, 11:25 PM

RE: Model 70 - by mg34.42 - 03-18-2018, 03:32 PM

View a Printable Version

Users browsing this thread: 9 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me