Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Akai Terecorder M7
#9

ATP (all tests passed) and ready to go.

I recorded about a half hr. from off of my cellphone and the reproduction is very good. I am going to keep this one.

For future searches: One thing I must add is that the "mic" level  input is not really and the line level input is probably looking for somethin around 100mv or more. So it takes more input than I expected and a mic will need a preamp (probably). Using my CP input on the mic level input with both the cell and the input level at about 10% was fine. The CP turned all the way up (source) and the level set at about 90% also worked using the line input but was much more likely to have some noise (not hum) between songs. It's all about voltage (again).

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/


Messages In This Thread
Akai Terecorder M7 - by Phlogiston - 01-28-2018, 02:49 PM
RE: Akai Terecorder M7 - by sam - 01-29-2018, 12:27 PM
RE: Akai Terecorder M7 - by Arran - 01-30-2018, 03:42 AM
RE: Akai Terecorder M7 - by Ron Ramirez - 01-30-2018, 07:13 AM
RE: Akai Terecorder M7 - by Phlogiston - 01-30-2018, 10:51 AM
RE: Akai Terecorder M7 - by Ron Ramirez - 01-30-2018, 12:06 PM
RE: Akai Terecorder M7 - by Phlogiston - 01-30-2018, 12:53 PM
RE: Akai Terecorder M7 - by Phlogiston - 01-30-2018, 04:46 PM
RE: Akai Terecorder M7 - by Phlogiston - 02-01-2018, 05:10 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM
Looking for verification of correct schematic.
Klondike98, Thank you. I'll double check that SN and get back to you. GarySP, Thank you for the schematic.RossH — 12:13 AM

[-]
Who's Online
There are currently 1364 online users. [Complete List]
» 1 Member(s) | 1363 Guest(s)
Avatar

>