1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-624 Mail Filter Cap 34 is NON-POLARIZED
tbone
Senior Member
****
Posts: 284
Threads: 18
Joined: Nov 2016
City: Cromwell State, Province, Country: CT
#15

02-03-2018, 04:36 PM
The use of film caps is a good idea. In the case of this receiver and its quick warmup tubes, you would be able to use the 400 volt version of the AES caps mentioned. This would make it easier for restuffing. I wouldn’t expect to see anything over 200 DC and the film caps would handle the ripple ok.

630 V film caps a great in AC transformer sets where the startup voltage can exceed 500 volts.

Just a thought.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
RE: 37-624 Mail Filter Cap 34 is NON-POLARIZED - by tbone - 02-03-2018, 04:36 PM
[No subject] - by Chuck Schwark - 02-25-2008, 09:28 PM
[No subject] - by davemc - 02-26-2008, 07:13 AM
[No subject] - by Ron Ramirez - 02-26-2008, 07:59 AM
[No subject] - by davemc - 02-26-2008, 08:13 AM
[No subject] - by Steve D - 02-26-2008, 12:38 PM
[No subject] - by davemc - 02-26-2008, 01:06 PM
[No subject] - by davemc - 03-03-2008, 06:07 PM
[No subject] - by Ron Ramirez - 03-03-2008, 11:10 PM
[No subject] - by davemc - 03-14-2008, 05:25 PM
[No subject] - by Ron Ramirez - 03-20-2008, 10:58 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1027 online users. [Complete List]
» 1 Member(s) | 1026 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration