Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

16X Speaker cloth etc.
#13

A little work today... I cut a piece of board to the right size, and bought the correct size hole saw. Then I tried to make a few practice holes on the scrap material. Sometimes this is really worthwhile. Now I know suitable drill speeds and which direction to cut. Next, to mark out the panel in the appropriate pattern and start making holes. ~100 of them!

I don't hold with furniture that talks.


Messages In This Thread
16X Speaker cloth etc. - by EdHolland - 12-01-2017, 05:42 PM
RE: 16X Speaker cloth etc. - by KCMike - 12-01-2017, 06:30 PM
RE: 16X Speaker cloth etc. - by EdHolland - 12-01-2017, 06:37 PM
RE: 16X Speaker cloth etc. - by Ron Ramirez - 12-01-2017, 07:08 PM
RE: 16X Speaker cloth etc. - by EdHolland - 12-02-2017, 04:37 PM
RE: 16X Speaker cloth etc. - by EdHolland - 01-08-2018, 08:33 PM
RE: 16X Speaker cloth etc. - by morzh - 01-22-2018, 01:31 PM
RE: 16X Speaker cloth etc. - by EdHolland - 01-26-2018, 11:22 PM
RE: 16X Speaker cloth etc. - by PhilcoPhan1936 - 01-27-2018, 01:58 AM
RE: 16X Speaker cloth etc. - by EdHolland - 01-27-2018, 01:24 PM
RE: 16X Speaker cloth etc. - by EdHolland - 02-02-2018, 04:53 PM
RE: 16X Speaker cloth etc. - by EdHolland - 02-03-2018, 09:34 PM
RE: 16X Speaker cloth etc. - by EdHolland - 02-11-2018, 10:01 PM
RE: 16X Speaker cloth etc. - by EdHolland - 02-13-2018, 06:38 PM
RE: 16X Speaker cloth etc. - by Brad Winder - 02-14-2018, 10:24 AM
RE: 16X Speaker cloth etc. - by EdHolland - 02-15-2018, 12:15 PM
RE: 16X Speaker cloth etc. - by EdHolland - 03-04-2018, 11:04 PM
RE: 16X Speaker cloth etc. - by EdHolland - 03-17-2018, 10:16 PM
RE: 16X Speaker cloth etc. - by EdHolland - 03-22-2018, 01:01 PM
RE: 16X Speaker cloth etc. - by EdHolland - 03-27-2018, 10:18 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Delco car radio Peko vibrator converstion issues
Rich, There is an Australian website (Cool386.com) that has much useful info regarding repair and restoration of vibr...Joe Rossi — 07:29 PM
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM

[-]
Who's Online
There are currently 3979 online users. [Complete List]
» 4 Member(s) | 3975 Guest(s)
AvatarAvatarAvatarAvatar

>