model 18 no reception

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

model 18 no reception

madsowry
Member

Posts: 124
Threads: 18
Joined: Jan 2018
City: Kingsville Ohio

#17

02-04-2018, 05:34 PM

Thanks Terry I will rewind it and not that I know even what I'm doing I agree after the 2 radio test it has to be the oscillator coil. I rewound it before using 40 gauge and 17 wraps. So if I wrap 19 or 20 will that be sufficient or just play with it with jumpers until I get a full dial? Thanks

Dick

Find

« Next Oldest | Next Newest »

Messages In This Thread

model 18 no reception - by madsowry - 02-01-2018, 11:03 PM

RE: model 18 no reception - by morzh - 02-02-2018, 08:14 AM

RE: model 18 no reception - by Radioroslyn - 02-02-2018, 09:04 AM

RE: model 18 no reception - by madsowry - 02-02-2018, 03:28 PM

RE: model 18 no reception - by morzh - 02-02-2018, 10:16 PM

RE: model 18 no reception - by madsowry - 02-03-2018, 12:59 PM

RE: model 18 no reception - by madsowry - 02-03-2018, 03:30 PM

RE: model 18 no reception - by Radioroslyn - 02-03-2018, 04:52 PM

RE: model 18 no reception - by madsowry - 02-03-2018, 05:54 PM

RE: model 18 no reception - by morzh - 02-03-2018, 06:24 PM

RE: model 18 no reception - by madsowry - 02-03-2018, 06:54 PM

RE: model 18 no reception - by morzh - 02-03-2018, 07:11 PM

RE: model 18 no reception - by madsowry - 02-03-2018, 11:08 PM

RE: model 18 no reception - by morzh - 02-04-2018, 09:51 AM

RE: model 18 no reception - by madsowry - 02-04-2018, 01:08 PM

RE: model 18 no reception - by Radioroslyn - 02-04-2018, 05:17 PM

RE: model 18 no reception - by madsowry - 02-04-2018, 05:34 PM

RE: model 18 no reception - by madsowry - 02-05-2018, 01:50 PM

RE: model 18 no reception - by Radioroslyn - 02-05-2018, 02:53 PM

RE: model 18 no reception - by madsowry - 02-05-2018, 07:11 PM

RE: model 18 no reception - by madsowry - 02-06-2018, 03:51 PM

RE: model 18 no reception - by morzh - 02-06-2018, 07:38 PM

RE: model 18 no reception - by madsowry - 02-06-2018, 11:01 PM

RE: model 18 no reception - by madsowry - 02-09-2018, 05:32 PM

RE: model 18 no reception - by Radioroslyn - 02-09-2018, 07:27 PM

RE: model 18 no reception - by madsowry - 02-09-2018, 08:59 PM

RE: model 18 no reception - by Radioroslyn - 02-10-2018, 09:37 AM

RE: model 18 no reception - by madsowry - 02-11-2018, 11:07 PM

RE: model 18 no reception - by Radioroslyn - 02-12-2018, 08:15 AM

RE: model 18 no reception - by madsowry - 02-23-2018, 12:00 AM

RE: model 18 no reception - by morzh - 02-23-2018, 07:53 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old. My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum. Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me