Zenith 8s359

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Zenith 8s359

klondike98
Phorum Moderator

Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR

02-05-2018, 01:51 AM

The dial pointer has a definite bow to it! Has anyone straightened one of these before? It doesn't actually look too bad when viewing it straight on so I don't want to make things worse.

[Image: https://www.dropbox.com/s/2b6ttthprr9ngs....jpg?raw=1]

Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Zenith 8s359 - by klondike98 - 02-03-2018, 01:56 PM

RE: Zenith 8s359 - by Electrothaumaturgist - 02-03-2018, 05:05 PM

RE: Zenith 8s359 - by murf - 02-03-2018, 05:33 PM

RE: Zenith 8s359 - by morzh - 02-03-2018, 10:20 PM

RE: Zenith 8s359 - by klondike98 - 02-04-2018, 12:22 AM

RE: Zenith 8s359 - by Arran - 02-04-2018, 02:15 AM

RE: Zenith 8s359 - by klondike98 - 02-04-2018, 04:38 PM

RE: Zenith 8s359 - by Electrothaumaturgist - 02-04-2018, 09:02 PM

RE: Zenith 8s359 - by klondike98 - 02-05-2018, 01:51 AM

RE: Zenith 8s359 - by Arran - 02-05-2018, 05:09 AM

RE: Zenith 8s359 - by Phlogiston - 02-05-2018, 11:43 AM

RE: Zenith 8s359 - by klondike98 - 02-12-2018, 01:02 PM

RE: Zenith 8s359 - by OldRestorer - 02-12-2018, 01:38 PM

RE: Zenith 8s359 - by Radioroslyn - 02-12-2018, 02:53 PM

RE: Zenith 8s359 - by klondike98 - 02-12-2018, 08:20 PM

RE: Zenith 8s359 - by Arran - 02-14-2018, 04:22 AM

RE: Zenith 8s359 - by klondike98 - 02-14-2018, 07:15 PM

RE: Zenith 8s359 - by klondike98 - 03-15-2018, 07:48 PM

RE: Zenith 8s359 - by Radioroslyn - 03-15-2018, 08:52 PM

RE: Zenith 8s359 - by klondike98 - 03-15-2018, 09:02 PM

RE: Zenith 8s359 - by Electrothaumaturgist - 03-17-2018, 08:57 PM

RE: Zenith 8s359 - by klondike98 - 03-18-2018, 01:10 PM

RE: Zenith 8s359 - by Radioroslyn - 03-18-2018, 02:05 PM

RE: Zenith 8s359 - by klondike98 - 03-18-2018, 02:13 PM

RE: Zenith 8s359 - by Radioroslyn - 03-18-2018, 05:13 PM

RE: Zenith 8s359 - by klondike98 - 03-18-2018, 07:33 PM

RE: Zenith 8s359 - by Radioroslyn - 03-18-2018, 09:00 PM

RE: Zenith 8s359 - by klondike98 - 03-19-2018, 01:30 AM

RE: Zenith 8s359 - by klondike98 - 03-25-2018, 04:56 PM

RE: Zenith 8s359 - by Radioroslyn - 03-25-2018, 07:14 PM

RE: Zenith 8s359 - by klondike98 - 03-25-2018, 11:26 PM

RE: Zenith 8s359 - by klondike98 - 03-30-2018, 07:47 PM

RE: Zenith 8s359 - by klondike98 - 08-29-2018, 11:44 PM

RE: Zenith 8s359 - by tbone - 08-31-2018, 11:32 AM

RE: Zenith 8s359 - by Eliot Ness - 08-31-2018, 12:15 PM

RE: Zenith 8s359 - by klondike98 - 08-31-2018, 12:29 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me