1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
model 18 no reception
madsowry
Member
***
Posts: 124
Threads: 17
Joined: Jan 2018
City: Kingsville Ohio
#20

02-05-2018, 08:11 PM
I aligned it as best I could.  I hooked everything up as they say and hooked the out put meter to the output trans. and the meter was at halfway across the dial.  But my SG seems to be at full attenuation all the time.  I can't turn it down cause its all the way down now.  Without that the meter stays in 1 spot no matter how much you move the condensers.  Could this thing be stuck in AVC or is my SG screwed up.  At the low end of the dial I get blasted out by one station and can't hardly hear any other stations.  Might just stick this one on the shelf and try something else.  Thanks

Dick
Find
« Next Oldest | Next Newest »


Messages In This Thread
model 18 no reception - by madsowry - 02-02-2018, 12:03 AM
RE: model 18 no reception - by morzh - 02-02-2018, 09:14 AM
RE: model 18 no reception - by Radioroslyn - 02-02-2018, 10:04 AM
RE: model 18 no reception - by madsowry - 02-02-2018, 04:28 PM
RE: model 18 no reception - by morzh - 02-02-2018, 11:16 PM
RE: model 18 no reception - by madsowry - 02-03-2018, 01:59 PM
RE: model 18 no reception - by madsowry - 02-03-2018, 04:30 PM
RE: model 18 no reception - by Radioroslyn - 02-03-2018, 05:52 PM
RE: model 18 no reception - by madsowry - 02-03-2018, 06:54 PM
RE: model 18 no reception - by morzh - 02-03-2018, 07:24 PM
RE: model 18 no reception - by madsowry - 02-03-2018, 07:54 PM
RE: model 18 no reception - by morzh - 02-03-2018, 08:11 PM
RE: model 18 no reception - by madsowry - 02-04-2018, 12:08 AM
RE: model 18 no reception - by morzh - 02-04-2018, 10:51 AM
RE: model 18 no reception - by madsowry - 02-04-2018, 02:08 PM
RE: model 18 no reception - by Radioroslyn - 02-04-2018, 06:17 PM
RE: model 18 no reception - by madsowry - 02-04-2018, 06:34 PM
RE: model 18 no reception - by madsowry - 02-05-2018, 02:50 PM
RE: model 18 no reception - by Radioroslyn - 02-05-2018, 03:53 PM
RE: model 18 no reception - by madsowry - 02-05-2018, 08:11 PM
RE: model 18 no reception - by madsowry - 02-06-2018, 04:51 PM
RE: model 18 no reception - by morzh - 02-06-2018, 08:38 PM
RE: model 18 no reception - by madsowry - 02-07-2018, 12:01 AM
RE: model 18 no reception - by madsowry - 02-09-2018, 06:32 PM
RE: model 18 no reception - by Radioroslyn - 02-09-2018, 08:27 PM
RE: model 18 no reception - by madsowry - 02-09-2018, 09:59 PM
RE: model 18 no reception - by Radioroslyn - 02-10-2018, 10:37 AM
RE: model 18 no reception - by madsowry - 02-12-2018, 12:07 AM
RE: model 18 no reception - by Radioroslyn - 02-12-2018, 09:15 AM
RE: model 18 no reception - by madsowry - 02-23-2018, 01:00 AM
RE: model 18 no reception - by morzh - 02-23-2018, 08:53 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration